D L S M A R I N E S P E A K E R S
Thank you for buying a DLS MARINE speaker.
This manual will show you how to do a correct instal-
lation. Please read the entire manual before you begin
the installation.
Features and benefits:
- Excellent audio performance, transparent
and clear sound
- Water protected design, IP54 class
- Easy installation
Installation
Install the speakers in a solid and stable panel to get the best
sound quality. Use the template to cut and drill. Fasten with
stainless steel screws. Make sure to connect with the same pola-
rity on both speakers.
NOTE!
Avoid an installation close to the magnetic compass, the
speaker magnets can influence the compass needle.
The
Marine 225
and
Marine 226
are designed for use both out-
doors and indoors on a vessel or yacht. These speakers are well
protected against water.
Break-in period
Allow the speakers to play at normal volume for at least 15-20
hours. After this time the performance is correct.
Technical Assistance
For technical assistance ask the shop where the product was sold
or the distributor in your country. You can also send an e-mail to
Information can also be found on our web-site www.dls.se
We follow a policy of continuous advancement in development.
For this reason all or part of specifications & designs may be
changed without prior notice.
Warranty service
This speaker is covered by warranty, depending on the condi-
tions in the country where it is sold. If the speaker is returned for
service, please include the original dated receipt (or a copy) with
the product.
WARNING
While these speakers are specially designed for marine applica-
tions, they are not fully waterproof which must be taken in consi-
deration when doing the installation.
DLS MARINE SPEAKERS
OWNERS MANUAL
DLS Svenska AB 2015-08-20
Marine 225
Marine 226
Safety Considerations:
Your speakers must be installed in a manner which does
not interfere with your vessel’s factory installed electronic
devices. You should also take the time to securely mount
them so that they do not come loose in the event of a col-
lision or a sudden jolt to the vessel.
- Check before drilling any holes in your vessel to make
sure that you will not be drilling through the hull, a fuel tank,
fuel line, wiring harness or other vital vessel system.
- Protect all wiring from sharp edges (metal, fibreglass,
etc.) by carefully routing them, tying them down and using
grommets and loom where appropriate.
Crossover connection of Marine 225
Connection of Marine 226
Input from
stereo / amplifier
+
_
+
_
More facts:
Model
Marine 225
Marine 226
Size
5,25” / 13 cm
6,5” / 16,5 cm
Tweeter
16 mm /0,63”
16 mm / 0,63”
Nom. power (RMS)
60 W
60 W
Maximum power
100 W
100 W
Frequency range
80 Hz - 18 kHz
70 Hz - 18 kHz
Magnet diameter
80 mm / 3,15”
80 mm / 3,15”
Outer diameter
165 mm / 6,5”
190 mm / 7,48”
Mounting depth
71 mm / 2,8”
76 mm / 3”
Mounting hole
121 mm / 4,76”
145 mm / 5,7”
DLS Svenska AB
P.O. Box 13029
SE-40251 Göteborg, Sweden
Tel: +46 31 84 00 60
Fax: +46 31 84 40 21
E-mail: [email protected]
www.dls.se
(Blue marking)
T
(Red marking)
Red cable (+ tweeter)
Blue cable (+ woofer)
Black cable (- ground)
Crossover
Head unit or
amplifier
+ -
red black
Grille mounting
Important:
Before installation the grille has to be removed. After in-
stallation make sure the grille is remounted in the same
way so the water drain hole is facing down, see photo!
Water drain hole.
