DLS PERFORMANCE SPEAKERS
OWNERS MANUAL
Welcome
Thank you for buying a DLS speaker. This model is a part of
DLS Performance speaker line.
Install the speakers yourself if you feel confident with our in-
structions and if you have the proper tools. A poor installation
job can destroy the final result even from these speakers, so if
you feel unsure, turn over the installation job to someone better
suited to it.
Two-way coaxial system
These speakers have small installation depth and fits mots
modern vehicles. Install the filters in a dry place. Fasten them
with wire ties or similar. If installed in the door side face the con-
nections downwards to avoid moisture inside the crossover box.
On the right you can see how to connect the crossovers.
Installation
Speaker drivers:
Mount the speakers in the door sides of your car. We recom-
mend you to install the drivers in a strong baffle of MDF-board
or similar, this will improve the sound very much. For baffle
installation se our advices on next page. If it is possible you
should attach an asphalt damping mat to the door inside, this
will furher improve the sound.
It is important to fasten the speakers properly in order to avoid
bad sound or rattling
Crossovers:
It’s vital that they are attached properly to the interior of the
vehicle. Don’t place them close to the internal wiring of the car,
this can cause interference. Install them in a dry place. Fasten
them with screws or wire ties. If installed in the door side face
the connections downwards to avoid moisture inside the cros-
sover box.
The crossovers must be used, if you connect without them
the sound becomes bad and you will destroy the tweeter.
Wiring:
Use high quality speaker cables. Make sure the cables don’t
get jammed causing a short circuit to ground. This can dama-
ge the output circuits of your head unit or amplifier.
Break-in period
Allow the speakers to play at normal volume for at least 15-20
hours. After this time the performance will be correct.
Technical Assistance
For technical assistance ask the shop where the product was
sold or the distributor in your country.
You can also send an e-mail to [email protected]
Information can also be found on our web-site www.dls.se
We follow a policy of continuous advancement in development.
For this reason all or part of specifications & designs may be
changed without prior notice.
Warranty service
This speaker is covered by warranty, depending on the condi-
tions in the country where it is sold. If the speaker is returned
for service, please include the original dated receipt (or a copy)
with the product.
Speaker phasing
To be sure to have the correct speaker polarity (phase) you
can check this by using a 1,5 Volt battery.
Connect a cable from the battery plus-pole to the speaker
plus, and a cable from the battery minus to the speaker
minus.
When the speakers are correctly connected the speaker cone
should move outwards on both right and left channel.
This check must be made on the cables going from the spea-
kers, to the output terminals of your car stereo or amplifier.
DLS Svenska AB
Tagenevägen 11B
SE-
42259 Hisings Backa
, Sweden
Tel: +46 31 840060
E-mail: [email protected]
www.dls.se
M526
i
2-way coaxial
Connection of speaker
Make sure you connect the cables with correct polarity to the
speakers. Observe the markings on the terminals. The red
and blue marked terminal are plus and the black small termi-
nal is the common minus.
Technical data:
M 526
i
Article number
Bass driver
CC-M526i
165 mm / 6,5”
Tweeter
20 mm soft dome
Impedance
4 ohm
Nom. RMS power
50 Watt
Max / Peak-power
75 / 150 Watt
Frequency range
60 Hz - 20 kHz
Magnet size
80 mm / 3,15”
Mounting hole
146 mm (5,75”)
Mounting depth
43 mm ( 1,7”)
T
Speaker terminal connection M526
i
Head unit or
amplifier
- +
Minus -
Red cable (+ tweeter)
Blue cable (+ woofer)
Black cable (- common ground)
It is enough to con-
nect to only one
of the woofer - or
tweeter - terminals
on the crossover.
