background image

SERIAL NUMBERS

 

The lawn mower has three serial numbers:

 

Mower Number — Located on frame at right rear transaxle mount. Transaxle Number — Located on transaxle. Engine 

Number — Located on engine. When referring to serial number on Warranty Registration, etc., use Mower Serial Number 

located on frame.

 

SAFETY INSTRUCTIONS

 

BEFORE MOWING

 

1. Read these safety instructions and engine manufacturer's 

operating and maintenance instructions that are furnished 

with the mower.

 

2. Discuss proper maintenance with your Dixon dealer, to 

save money and prevent injury. Consult your dealer before 

removing any parts.

 

3. Don't allow anyone to operate your Dixon mower without 

proper instruction. Young children should never be allowed 

to operate any power mower, riding or walking.

 

4. Before mowing, pick up all debris—particularly stones and 

sharp objects.

 

5. Before starting the engine, make sure the gas cap is in 

place.

 

DURING MOWER OPERATION

 

1. The revolutionary Dixon mower att racts many admiring 

neighbors. But when mowing, all persons  — especially 

children  — and pets should be cleared from the mowing 

area.

 

2. Wear appropriate, safe clothing when mowing  — close-

fitting jeans or slacks and heavy leather or safety shoes 

with rough soles. Never use any kind of mower with bare 

feet or open sandals, not even an old push-type model!

 

3. When grass is wet or slippery, do not use any riding mower.

 

4. Always mow at the slowest speed that will cut satisfactorily.

 

5. Keep hands and feet away from the blade at all times.

 

6. Although the Dixon mower is equipped with a missile

 

deflector, keep persons clear of the discharge chute. Do not operate mower unless deflector is in place.

7. Use extreme caution when mowing hills or slopes with 

any 

mower.

 

8. Always disengage blades before taking the mower across 

walks or objects that project above the surface.

 

9. When the mower is not in use, turn the engine off; never 

leave the engine running unattended. Your Dixon mower is 

equipped with a weight-sensitive switch that kills the engine 

when operator leaves the seat while blades are engaged. 

Test this important safety feature before each time mower is 

used. This may be done by starting engine, engaging blades 

and then rising slightly from seat. If engine does not stop, 

see your dealer for necessary repair.

 

10. Before adjusting your mower or adding fuel, turn the en -

gine off. Let it cool, and disconnect the spark plug so the 

engine cannot start by accident. Be sure all moving parts 

are stopped.

 

11. Never run the engine indoors; the fumes are dangerous.

 

12. Before backing your Dixon mower, stop, turn around, and 

look.

 

13. Gasoline fumes are explosive; use only approved gasoline 

containers to store small amount of fuel. No special oil/gas 

mixtures are needed for your Dixon mower.

 

14. If the mower should start vibrating, stop the engine imme-

diately and check for damage or loose parts. Vibration is 

usually the warning of trouble.

 

15. Never lift lawn mower by the body; lift only by the frame.

 

16. Never carry passengers.

 

Summary of Contents for ZEETER 422 & 424


















Reviews: