background image

55

TROUbleshOOTINg gUIDe

Problem

Cause

Engine overheats.

•  Clogged air intake or cooling fins.
•  Engine overloaded.
•  Poor ventilation around engine.
•  Defective engine speed regulator.
•  Too little or no oil in the engine.
•  Fouled spark plug.

Battery not charging.

•  Poor contact with battery terminal cable 

connectors.

•  Charging lead is disconnected.
•  Fault in engine charging system.

Machine moves slowly, unevenly, or not at all.

•  Parking brake on.
•  Bypass valve on pump open.
•  Drive belt for the transmission gears slack or has 

come off.

•  Air in hydraulic system.

Mower deck not engaging.

•  Drive belt for the mower deck has come loose.
•  Contact for the electromagnetic coupling has 

loosened.

•  The blade switch is faulty or has come loose, from 

the cable contact.

•  The fuse has blown.

Hydraulic drive leaks oil.

•  Damaged seals, housing, or gaskets.
•  Air trapped in hydraulic system.

Uneven mowing results.

•  Unequal tire pressure on the left and right sides.
•  Bent blades.
•  Suspension for the mower deck is uneven.
•  Blades are dull.
•  Driving speed too high.
•  The grass is too long.
•  Grass collected under the mower deck.

Machine vibrates.

•  Blades are loose.
•  Blades are incorrectly balanced.
•  Engine is loose.

Summary of Contents for GRIZZLY SE 6029FX









































































Reviews: