CH 03515
Diagram & Adjustment
Caution
1. Do not attempt to disassemble the camera.
In order to prevent electric shock, do not remove screws or cover.
2. Handle the camera with care.
The camera could be damaged by improper handling or storage
3. Do not expose the camera to rain or moisture, or try to operate in wet
areas.
Take immediate action if the camera becomes wet. Turn the power off and
request service to qualified personnel. Moisture can damage the camera and
also create a risk of electric shock.
4. Do not use strong or abrasive detergents when cleaning the camera body.
Use a dry cloth to clean the camera when dirty. In case the dirt is hard to
remove, use a mild detergent and wipe gently.
5. Never point the camera toward the sun.
Whether the camera is used outdoor or not, never point it toward the sun. Use
with caution when operating the camera in the vicinity of spot lights or other
bright lights and light reflecting objects.
6. Do not operate the camera beyond its temperature, humidity, or power
source ratings.
Do not use the camera in an extreme environment where high temperature or
high humidity exists. Use the camera under conditions where temperatures are
between 14 F~122 F (-10 C~+50 C), and humidity is below 85%,
SA 1965
The symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the
product's enclosure that may be sufficient magnitude to constitute a risk of electric shock to persons.
To prevent electric shocks and risk of fire hazards,
DO NOT use other than specified power source.
CAUTION:
!
C A U T I O N
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER OR BACK. NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
To prevent fire or shock hazard, do not expose the unit to rain or moisture. The symbol is intended to alert
the user to the presence of important operating and maintenance (servicing) instructions in the literature
accompanying the appliance.
SA 1966
!
WARNING
CAUTION
This equipment has been tested and found to comply with the limits for a Class A. Digital
device. Pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with
the instruction manual, it may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user will be required
to correct the interference at own expense.
Any changes or modifications in construction of this device which are not expressly
approved by the party responsible for compliance could void the user's authority to operate the equipment.
o
o
o
o
Installation
1. Opening the dome : Push the latch button.
2. Removing the dome : Lift the dome case.
3. Camera installation & Lens adjustment.
1) Fix the mount bracket with supplied
screw on ceiling or wall mount.
Note : The camera front sign is on the
mount bracket.
2) Attach the main body to the mount
bracket by rotating it.
3) By turning the
①
(Tele-Wide) knob,
you can access a range of focal lengths
4) Since then, by turning the
②
(Near-Far) knob, you can set the focus
5) Reassemble dome case.
Installation
IR DOME Camera
3
-
axis
Composition
Main Product Mount Bracket
SCREW TP1
4X30 3EA
1. Push the button inside of main
body and turn the main body
counterclockwise.
2. Detach the main body from mount
Removing Mount Bracket
1. Pan adjustment : Grasp the lens cover and then adjust direction to the
right or left. ('D' -180˚~+180˚)
2. Tilt adjustment : Grasp the lens cover and then adjust direction to the
up or down ('A' : 18˚~90˚ or 'B' 21˚~90˚)
3. Roll adjustment : grasp the lens cover and then rotate ('C' : -180˚~+180)
Angle Adjustment
<Focus Adjustment>
User Manual Screws & Anchor