Ditch Witch 420sx Operator'S Manual Download Page 67

Page: 67 / 141

Plow - 66

420sx Operator’s Manual

Operation

CMW

Operation

Crushing weight could cause death or serious injury. Use proper

procedures and equipment or stay away.

Electrical shock. Contacting electrical lines will cause death or serious

injury. Know location of lines and stay away.

NOTICE:

Cutting high voltage cable can cause electrocution. Expose lines by hand before digging.

Incorrect procedures could result in death, injury, or property damage.

Learn to use equipment correctly.

NOTICE:

•

Comply with all utility notification regulations before plowing, digging, or drilling.

•

Notify companies that do not subscribe to One-Call.

•

Keep skid shoes in contact with the ground during operation.

•

Operate the plow with blade fully in the ground.

•

Do not drive in reverse with blade in the ground.

Summary of Contents for 420sx














































































































































Search results

Summary of Contents for 420sx

Reviews:

Brands by name

Popular brands

Ditch Witch 420sx, Operator'S Manual

Search results

Summary of Contents for 420sx

Reviews:

Brands by name

Popular brands