manualshive.com logo in svg

Ditch Witch 420sx, Operator'S Manual

Share
Download
Ditch Witch 420sx Operator'S Manual Download Page 62

420sx Operator’s Manual

Transport - 61

Tow

CMW

Tow

Under normal conditions, tractor should not be towed. If tractor becomes disabled and towing is 
necessary:

•

Open hydrostat bypass valve (shown). 

•

Do not tow for more than 200 yd (180 m).

•

Tow at less than 1 mph (1.6 km/h).

•

Use maximum towing force of 1.5 times unit weight.

Procedure 

1. Attach tow line to all available tie-down points facing towing vehicle.

2. Turn hydrostat bypass valve 90° clockwise to open valve.

3. Fasten seat belt.

4. Disengage parking brake.

5. Check that ground drive and attachment speed/direction controls are in neutral position.

Incorrect procedures could result in death, injury, or property damage. 

Learn to use equipment correctly.

Incorrect procedures could result in death, injury, or property damage. 

Learn to use equipment correctly.

Summary of Contents for 420sx














































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands