DirecTV Advanced Installation Meter 2 Operation Manual Download Page 97

Page: 97 / 108

Page 97

AIM 2 Operation Manual

Deleting Records

You can delete records stored on the AIM, including:

• An individual record
• All records for a selected account
• All records for all accounts
•

All records of a selected type (EIV, EIV

Plus, Guided Mode, Transponder Survey, or

Screenshots).

1. Press

CONFIG

to go to the

CONFIGURATION

screen.

2. Highlight

Records

and press

SELECT

to go to

the

RECORDS MAIN

screen. Then highlight

one of the following:

• To delete all records on the AIM or

records of a selected type, highlight

Quick Delete All

and press

SELECT

Go to Step 3.

• To delete an individual record, highlight

View All Records

and press

SELECT

Go to Step 4.

• To delete all records for an account,

highlight

View By Account Number

and

press

SELECT

. Go to Step 5.

Summary of Contents for Advanced Installation Meter 2













































































































Search results

Summary of Contents for Advanced Installation Meter 2

Reviews:

Related manuals for Advanced Installation Meter 2

Brands by name

Popular brands

DirecTV Advanced Installation Meter 2, Operation Manual

Search results

Summary of Contents for Advanced Installation Meter 2

Reviews:

Related manuals for Advanced Installation Meter 2

Brands by name

Popular brands