DirecTV Advanced Installation Meter 2 Operation Manual Download Page 78

Page: 78 / 108

Page 78

AIM 2 Operation Manual

Performing a Satellite Tune Test

You can use the AIM’s Satellite Tune feature to tune to any DIRECTV transponder. Connecting

the AIM in different locations in the distribution network, you can progressively test each

segment of the connection between the ODU and the IRD to locate a problem.

Set up the job for the installation. See the

Starting a Job

section in

Chapter 5

2. From the

HOME

screen, press

TEST

to go to

the

TEST

screen.

3. Highlight

Satellite Tune

and press

SELECT

to go to the

SAT TUNE CONFIGURATION

screen.

Highlight the equipment configuration for the

installation and press

SELECT

to go to the

SAT

TUNE LOCATION

screen.

5. Use the left/right arrow buttons to position the

image of the AIM under the location where you

are testing.

Summary of Contents for Advanced Installation Meter 2













































































































Search results

Summary of Contents for Advanced Installation Meter 2

Reviews:

Related manuals for Advanced Installation Meter 2

Brands by name

Popular brands

DirecTV Advanced Installation Meter 2, Operation Manual

Search results

Summary of Contents for Advanced Installation Meter 2

Reviews:

Related manuals for Advanced Installation Meter 2

Brands by name

Popular brands