DirecTV Advanced Installation Meter 2 Operation Manual Download Page 19

Page: 19 / 108

Page 19

AIM 2 Operation Manual

Power-Off

Press and hold the

POWER

button until the

SHUT DOWN AIM

screen appears.

Use the up/down arrow buttons to highlight

Shutdown

and press

The meter turns off.

Hard Reset

If the AIM is unresponsive to button presses, perform a hard reset.
Press and hold the

POWER

button for 10 to 30 seconds until the meter turns off.

Wait for several seconds, then press the

POWER

button again. The meter should turn back

on.

If the AIM does not turn on after a hard reset, connect the AIM

to the AC power adapter (see the Battery Charging section

later in this chapter), then press the POWER button.

If the meter still does not turn on, return the AIM to Trilithic

Customer Service. See the Return Policy section later in the

manual.

Summary of Contents for Advanced Installation Meter 2













































































































Search results

Summary of Contents for Advanced Installation Meter 2

Reviews:

Related manuals for Advanced Installation Meter 2

Brands by name

Popular brands

DirecTV Advanced Installation Meter 2, Operation Manual

Search results

Summary of Contents for Advanced Installation Meter 2

Reviews:

Related manuals for Advanced Installation Meter 2

Brands by name

Popular brands