DirecTV Advanced Installation Meter 2 Operation Manual Download Page 100

Page: 100 / 108

Page 100

AIM 2 Operation Manual

Transferring Records

You can transfer records from your AIM to a PC using a USB flash drive. You also can transfer

records from a USB flash drive to the AIM (see page 92). You can transfer:

• An individual record
• All records for a selected account
• All records for all accounts
•

All records of a selected type (EIV, EIV Plus,

Guided Mode, Transponder Surveys, or

Screenshots).

When transferring records between the AIM and a

USB flash drive, you can choose from two options:

• To retain a copy of the records on the device

you are transferring from, select

Copy

• To permanently delete the records from the

device you are transferring from, select

Move

Transferring records from the AIM to

a USB flash drive

Insert the USB flash drive in the appropriate

USB connector on the meter.

2. Press

CONFIG

to go to the

CONFIGURATION

screen.

3. Highlight

Records

and press

SELECT

to go to the

RECORDS MAIN

screen. Then

highlight one of the following options:

• To transfer all records on the AIM or records of a selected type, highlight

Quick Copy All

Quick Move All

and press

SELECT

. Go to Step 4.

• To transfer an individual record, highlight

View All Records

and press

SELECT

. Go to Step 5.

• To transfer all records for an account, highlight

View By Account Number

and press

SELECT

. Go to Step 6.

Summary of Contents for Advanced Installation Meter 2













































































































Search results

Summary of Contents for Advanced Installation Meter 2

Reviews:

Related manuals for Advanced Installation Meter 2

Brands by name

Popular brands

DirecTV Advanced Installation Meter 2, Operation Manual

Search results

Summary of Contents for Advanced Installation Meter 2

Reviews:

Related manuals for Advanced Installation Meter 2

Brands by name

Popular brands