Directive Systems & Engineering DSEFO144-12XPOL Manual Download Page 1

 
 

DSEFO144-12XPOL Rev 2/21 

Directive Systems & Engineering 

                     2702 Rodgers Terrace

 

              Haymarket, VA 20169-1628 

                             www.directivesystems.com 
                                      703-754-3876 

 

24 Element 2.5 wl. Dual Polarity K1FO Designed Yagi,  

Model DSEFO144-12XPOL 

                                                                 

 

ELECTRICAL SPECIFICATIONS 

 

         

Frequency range: MHz ......................144-146 
Gain: dBd........................................... 12.6 dBd (14.75 dBi) 
Impedance: Ohms.............................. 50 
Connector type................................... Type N(F) UG-58/U 
Front -to- back ratio: dB...................... 23 
SWR: Typical at resonance................ 

1.2:1 

Beamwidth: degrees 

E- Plane ................................. 34° 
H- Plane ................................. 37° 

Sidelobe level: decibels 

E- Plane.................................. -19 
H- Plane.................................. -16 

Power rating, Continuous: Watts .......  1000 
Stacking Distance: ft.(m) 

E- Plane.................................  

11’7” (3.53) 

      

         

H- Plane.................................  

10’8” (3.25) 

 

MECHANICAL SPECIFICATIONS 

 

Boom length: ft. (m.)........................... 

19’ (5.79) 

Turning radius: in. (m.)........................ 1

2’ (3.65) 

Weight Assembled: Lbs (kg.).............. 12 (5.44) 
Max mast size: in. (cm.)....................... 2

” (5.08) 

Wind surface area: Ft (m. ) ................. ~2 (.18) 
Wind Survival: Mph (km/hr)................. 100 (160) 

 

PARTS LIST

 

  

            

Note: All hardware is Stainless Steel, unless otherwise noted.

                                                                                            

 

Boom

1 1/4" Rea r Boom s ecti on 

1  (Red on front-wi th both Hori z & Vert el ement hol es -doubl e wa l l  thi cknes s )

1 3/8" Center Boom s ecti on

1  (Bl ue on front a nd Red on rea r-wi th both Hori z & Vert el ement hol es )

1 1/4" Front Boom s ecti on

1  (Green on front a nd Bl ue on rea r-wi th both Hori z & Vert el ement hol es )

1 1/8" Front Boom extens i on 

1  (Green on rea r)

El ement Bundl e

1/4" El ements

22

1/2" Dri ven El ement

2

3/8" T-a rms

4

Summary of Contents for DSEFO144-12XPOL












Reviews: