background image

6

933.SUBARU5 1.06.195.3 2014 Subaru BRZ (Smart Key)
©2022 VOXX•DEI LLC.  All rights reserved.

Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram (        ).

Hood Pin

Certification ECU

(white connector - C

behind glove box

Certification ECU

(white connector - A

behind glove box)

22-pin White Conn.

12-pin Black Conn.

8-pin White Conn.

THSUN2

(optional T-Harness)

Security Only

Mandatory Connections

Remote Start Only

Legend:

Remote Start + Security

22

8

12

4

2

4

4

2

Slide to open

A     module can also be used for 

this installation.

IMPORTANT:

Position the

fuses correctly!

MAIN (5A)  (+)

(-) RLY3 PK LIGHT (15A) (+)

(-)  ACC & STAR

T (30A)  (+)

(-)    FLEX RLY (20A)    (+)

IGN (20A)  (+)

MAIN (5A) (+)

(-) RLY3/PK LIGHT (15A) (+)

5

5

30

20

20

15

15

Wiring diagram 

with 

T-Harness (THSUN2)

Connect for 

manual 

transmission 

only.

Clutch

     Refer to the 

Optional starter disable 

connection 

section for relay details.

Immobilizer Data Interrupt (connector side): 

Lt. Green

Immobilizer Data Interrupt (vehicle  side): 

Lt. Green/White

(-) Hood Input: 

Gray

 

Siren

(+) Siren Output: 

Brown/Red

Cut

NOT USED

NOT USED

    (-) Driver’s 
Door Trigger: 

Yellow/Black

,

pin 18

HD1

(white connector

at driver’s kick)

1 13

14
15
16
17

18

19
20
21

31
32
33
34
35

36

37
38
39

22
23
24
25
26
27
28
29
30

40
41
42
43
44
45
46
47
48

2

3

4

5

6

7

8

9

10

11

12

(-) RAP Off Output: 

Lt.Green/Black

     CUT 

the 

Tan 

and 

Tan/Black 

loops.

5

3

1

2

Blower Motor Relay

(behind glove box)

(+) 12V: 

Red

, pin 5

(+) 12V Input: 

Red

6

7

5 4 3

2

27 26

23

24

25

35 34

33

32

1

22

30

31

21

29

20

18

19

17

11

12

13

14

15

16

10 9 8

28

ECM

(white connector - B

behind glove box)

Immo Data: 

Yellow

, pin 25

(-) Ground: 

Black

(-) GWA Output: 

Blue/White

 

Summary of Contents for 933.SUBARU5

























Reviews: