background image

21

©

2000 Directed Electronics, Inc.

QUICK REFERENCE GUIDE:

To lock/arm using your remote

To lock/arm the system press 

for one second. The doors will lock (if

connected). The LED will begin to flash. If installed, the optional
Failsafe

®

Starter Kill will prevent the vehicle’s starter from cranking if it

has been installed. The vehicle’s horn (if connected) will honk and the
parking lights will flash once to confirm arming of the system.

To unlock/disarm using your remote

To unlock/disarm the system press 

for one second. The doors will

unlock (if connected). If installed, the optional Failsafe

®

Starter Kill will

be deactivated and the vehicle’s horn (if connected) will honk twice and
the parking lights will flash twice.

Disabling the optional Failsafe

®

Starter Kill without a transmitter

Turn on the ignition. Press and release the Valet

®

switch within 10 sec-

onds. The LED will stop flashing and the vehicle should start. Be sure to
check with the installer for the location of the Valet

®

switch.

To remote start the vehicle

Press 

and 

simultaneously. The parking lights will turn on (if con-

nected) and the vehicle will start and run for the programmed amount
of time. 

To enter or exit Valet

®

Mode

Turn the ignition to the "ON" position. Turn the ignition back off. Press
and release the Valet

®

switch within 10 seconds. The status LED will

light steadily if you have entered Valet

®

Mode. To exit Valet

®

Mode,

repeat the steps above. The LED will turn off when exiting Valet

®

Mode.

To activate Panic Mode

Press and hold 

for 1.5 seconds.

To disable the remote start system

To disable the remote start, move the shutdown toggle switch to the OFF
position. 

Location of Shutdown Switch______________________________

Cut along dotted line and f

old f

o

r a quick and eas

y r

efer

ence to k

eep in y

our pur

se or w

allet.

Summary of Contents for Avital 3200


























Reviews: