background image

15

This feature allows your system's remote start unit to be tem-

porarily disabled to prevent the vehicle from being remote started

accidentally. This feature is useful if the vehicle is being serviced

or stored in an enclosed area. To disable the remote start, move

the shutdown toggle switch to the OFF position. The switch can

be installed in a location of your choice. Check with your installer

for recommended locations.  

LOCATION OF SHUTDOWN SWITCH

_________________________

Stealth Coding

Technology

The receiver and transmitters use a mathematical formula called an

algorithm to change their code each time the transmitter is used.

This technology has been developed to increase the security of the

unit. The control unit knows what the next codes should be. This

helps to keep the transmitter “in sync” with the control unit even

if you use the remote control out of range of the vehicle. Howev-

er, if the remote has been pressed many times out of range of the

vehicle, or the battery has been removed, it may fall out of sync with

the control unit and fail to operate the system. To re-sync the

remote simply press 

several times within range of the vehicle.

The alarm will automatically re-sync and respond to the transmit-

ters normally.

Disabling the Remote Start System

15

©

2000 Directed Electronics, Inc.

Summary of Contents for Avital 3200


























Reviews: