Dinstar DWG2000E User Manual Download Page 16

Page: 16 / 92

DWG2000E/F/G GSM/CDMA VoIP Gateway User Manual

_______________________________________________________________________________

Shenzhen Dinstar Technologies Co., Ltd.

Traffic Statistics

Calculates the net flow, including the total bytes of message received and

sent.

Version info

shows the current firmware version



Device Model: Model name of the device



Package version:

02230804 2013-05-29 18:51:05 beta,

02230804

is the version number



Software version:

02230804 2013-05-29 18:50:18, 02230804

is the

version number



Web version: the version number of web system.

The web version

must match with software



Userboard 0 Version: the firmware version of userboard slot 0



Userboard License ID: Contact with support when it display as

Invalid



Hardware version/DSP version/ SIMbox version

4.3.2 Mobile Information

Figure 4.3-2 Mobile Information

Table 4.3-2 Mobile Information

Parameters

Description

Port

Number of GSM/CDMA ports.

Type

Indicates the current type of network. Such as CDMA or GSM

IMSI

International Mobile Subscriber Identity, it is the uniquely identifies of

SIM card

Status

Indicates the connection status of current GSM / CDMA module

Remaining Call

Duration

It showing available total call minutes of SIM card while call limitation is

enabled.

Carrier

Displays the network carrier of current SIM card.

Signal Quality

Displays the signal strength of in each channels of GSM / CDMA.

BER

Its indicate error rates between Module and Base station(BTS)

Summary of Contents for DWG2000E





























































































Search results

Summary of Contents for DWG2000E

Reviews:

Related manuals for DWG2000E

Brands by name

Popular brands

Dinstar DWG2000E, User Manual

Search results

Summary of Contents for DWG2000E

Reviews:

Related manuals for DWG2000E

Brands by name

Popular brands