DINSEO DIX TIG GO 1806.M AC/DC, Operation Manual, Page: 3 / 30

3
•
TIG
- Excellent TIG welding characteristics.
- High frequency arc striking of TIG welding, precise and effi-
cient even from long distance.
- Using special TIG torches allows remote adjustment of weld-
ing current directly from the torch.
- The diameter of the electrode used is set to allow greater con-
trol of the ignition and dynamics of the arc.
- Standard built-in pulsation (from 0,5 to 2000 Hz) with provi-
sion for entering the SYN Pulse function.
- Square, mixed, sinusoidal, or triangular wave shape selector.
- Square welding wave frequency balancing / regulation and
“Balance Plus”.
•
MMA
- The VRD (Voltage Reduction Device) can be activated, which
reduces voltages to below 12 V, which means that the weld-
ing machine can be used in ambient conditions in which there
is a high electrical risk, thereby providing maximum opera-
tor safety.
- “Arc Force” adjustable to select the best dynamic character-
istics for the welding arc.
- “Hot Start” adjustable to improve ignition with particularly dif-
ficult electrodes.
- Anti-sticking function to avoid the electrodes sticking.
DIX TIG GO 1806.M AC/DC
•
The PFC device makes the wave form of the current absorbed si-
nusoidal, which results in no harmonic disturbance on the mains
and optimisation of absorption, which allows you to use the weld-
ing power source’s full power with a 16 A fuse, as well as ensur-
ing greater protection of the welding machine against fluctuations
in the power supply voltage.
DIX TIG GO 2506.M AC/DC R
•
Suitable for use on all robotic systems.
•
Optional robot interface that handles all process start/ stop sig-
nals, regulation of the principal welding parameters, and also
acts as a flexible, efficient interfacing system that meetsall Ana-
logue / Digital connection requirements.
Usage limits (IEC 60974-1)
The use of a welder is typically discontinuous, in that it is made up
of effective work periods (welding) and rest periods (for the posi-
tioning of parts, the replacement of wire and underflushing opera-
tions etc. This welder is dimensioned to supply a I
2
max nominal
current in complete safety for a period of work of X% of the total us-
age time. The regulations in force establish the total usage time to
be 10 minutes. The work cycle is considered to be X% of this period
of time. If the permitted work cycle time is exceeded, an overheat
cut-off occurs to protect the components around the welder from
dangerous overheating. Activation of thermal protection is signaled
by “t° C” flashing on control panel display (for further information
see the control panel manual). After several minutes the overheat
cut-off rearms automatically and the welder is ready for use again.
Technical data
The general technical data of the system are summarized in ta-
ble 1.
Table 1
Model
DIX TIG GO 1806.M AC/DC DIX TIG GO 2506.M AC/DC
TIG MMA TIG MMA
Power supply 50/60 Hz
V 1~ 230 ±20% 3~ 400 ±20%
Power supply: Z
max
Ω
(*) 0,092
Input power @ I
2
Max
kVA 6,5 7,0 9,6
Delayed fuse (I
2
@ 100%)
A 16 10
Power factor / cosφ
0,99 / 0,99 0,95 / 0,99
Efficiency degree
η
0,77 0,76 0,81
Open circuit voltage
V 100 100
Current range
A 5÷220 10÷180 5÷300 10÷250
Duty cycle @ 100% (40°C)
A 140 120 210 190
Duty cycle @ 60% (40°C)
A 180 150 250 220
Duty cycle @ X% (40°C)
A 220 (30%) 180 (30%) 300 (35%) 250 (40%)
Usable electrodes
mm 1,2÷2,4 1,6÷4,0 1,2÷4,0 1,6÷5,0
Standards
IEC 60974-1 • IEC 60974-3 • IEC 60974-10 IEC 60974-1 • IEC 60974-3 • IEC 60974-10
Protection class
IP 23 S IP 23 S
Insulation class
F F
Dimensions
mm 465 - 390 - 185 495 - 390 - 185
Weight
kg 15,5 19
IMPORTANT:
These systems, tested in accordance with the requirements of the EN/IEC 61000-3-3 standard, satisfy the requirements laid down by the EN/
IEC 61000-3-11 standard.
DIX TIG GO 1806.M AC/DC
(*) This equipment meets the requirements laid down in the EN/IEC 61000-3-12 standard on harmonic currents.
DIX TIG GO 2506.M AC/DC
This equipment complies with EN/IEC 61000-3-12 provided that the maximum permissible system impedance Z
max
is less than or equal to 0,092
at the interface point between the user’s supply and the public system. It is the responsibility of the installer or user of the equipment to ensure,
by consultation with the distribution network operator if necessary, that the equipment is connected only to a supply with maximum permissible
system impedance Z
max
less than or equal to 0,092.