manualshive.com logo in svg

Dini Group DN9002K10PCI, User Manual

Share
Download
Dini Group DN9002K10PCI User Manual Download Page 138

H A R D W A R E  

 

The daughter card interface includes a 400-pin MEG-Array connector, made by FCI. The 
daughter card header is arranged into three “Banks”, correlating to the banks of IO on the 
Virtex 5 FPGA.. Each of these banks connects to one or more “IO Banks” on the Virtex 5 
FPGA. This allows three different sets of voltage or timing requirements to be met on a single 
daughter card simultaneously. Each Bank on the daughter card is 62 signals. 

Other connections on the daughter card connector system include three dedicated, differential 
clock connections for inputting global clocks from an external source, power connections, bank 
VCCO power, a buffered power on reset signal. 

25.1

 

Daughter Card Physical 

The connectors used in the expansion system are FCI MEG-Array 400-pin plug, 6mm, part 
#84520-102. This connector is capable of as much as 10Gbs transmission rates using 
differential signaling. 

All daughter card expansion headers on the DN9002K10PCI are located on the bottom side of 
the PWB. This is done to eliminate the need for resolving board-to-board clearance issues, 
assuming the daughter card uses no large components on the backside. 

The “Plug” of the system is located on the DN9002K10PCI, and the “receptacle” is located on 
the expansion board. This selection was made to give a greater height selection to the daughter 
card designer. 

25.1.1

 

Daughter Card Locations and Mounting 

The 400-pin daughtercard header is located on the bottom (solder) side near the right side of the 
board. Each MEG-Array header on a Dini Group product has four standard-position mountain 

DN9002K10PCI User Guide 

www.dinigroup.com

 128 

 

Summary of Contents for DN9002K10PCI










































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands