background image

5

HOW TO MIX YOUR FUEL

Common mixtures are 25:1/30:1. If you fi nd your machine is 
too smoky please use the higher ratio which is 30:1 as seen in 
diagram C.

WHAT IS 25:1/30:1?

The fi rst part of the formula refers to how many parts of fuel 
as seen in diagram A. The second part of the formula refers to 
how many parts of oil (diagram B or C). For example, 25 parts 
of unleaded fuel or low octane to 1 part of two stroke oil or 30 
parts of unleaded or low octane fuel to 1 part of two stroke oil.

REMEMBER TO MIX WELL (SHAKE BOTTLE)

ONLY USE THIS RECOMMENDED 2 STROKE FUEL MIX WITH A GOOD QUALITY 2 STROKE OIL FROM YOUR LOCAL SUPPLIER, USING A MIX 
RATIO OF 25:1/30:1 IN THE MACHINE. UNLEADED OR LOW OCTANE FUEL ANY OTHER FUEL MUST BE USED IN A TWO STROKE MIX. MIX WELL 
AS RECOMMENDED. INCORRECT MIX COULD DAMAGE YOUR ENGINE VOIDING YOUR WARRANTY, USE THIS FUEL MIX EVERY TIME YOUR 
MACHINE IS IN OPERATION FOR THE BEST DINGO TOOLS PERFORMANCE YOU CAN EXPECT OUT OF YOUR DINGO TOOLS MACHINE.

1

:

25

OIL

600
576.92

500

400

300

200

100

GASOLINE

FULL

1

:

25

OIL

600
576.92

30:1

C

1

:

25

OIL

600
576.92

25:1

B

A

1

:

:

:

:

:

:

:

25

25

25

25

2

5

5

25

5

OI

O

O

O

O

O

O

O

L

L

L

L

600
576 92

57

57

7

7

7

57

7

7

6.

6.

.

6.

.

.

92

92

92

9

9

500

25

AT ALL TIMES PLEASE KEEP THE FUEL TANK FULL WHEN IN OPERATION, 
“AVOID HAVING THE YOUR ENGINE FINISHING OPERATION FROM FUEL 
STARVATION. FUEL TANKS BEING KEPT FULL AT ALL TIMES WILL IMPROVE 
YOUR MACHINE PERFORMANCE. 

FUEL RUNNING OUT WHILE IN OPERATION MAY DAMAGE YOUR ENGINE, 
PLEASE BE SURE TO REFILL THE TANK, KEEPING THE FUEL WELL FILLED 
DURING OPERATION IN ASSISTING AND AVOIDING BREAK DOWNS OR 
OPERATION INTERRUPTIONS. FUEL TANKS BEING EMPTIED DURING 
OPERATION, MAY RISK DEBRIS ALL FOREIGN OBJECTS ENTERING INTO 
THE FUEL INTAKE CONFIGURATION SYSTEM CAUSING BLOCKAGES, OVER 
HEATING AND EVEN PISTON FAILURE. TO AVOID THESE CIRCUMSTANCES 
PLEASE KEEP YOUR FUEL TANK WELL FILLED AT ALL TIMES, AVOIDING 
ENGINE BREAKS INCURRED, FROM THE RESULT OF  FUEL STARVATION.

Summary of Contents for 65CC










Reviews: