background image

DGM INSTALLATION AND MAINTENANCE MANUAL 

40 

 

700135-0000 Rev. O 

Send)  value.  These  are  the  only  two  functions  that  can  be  accessed  without  having  a 
valid passnumber entered. 

5.2  PANEL CONTROLS 

The  following  is  a  list  of  the  controls  located  on  the  front  panel  of  the  DGM.  Numerical 
buttons are for entering information such as time, zone numbers, and function numbers. 

5.2.1  READ 

Press  the  READ  button  after  entering  a  zone  number  to  display  the  status  of  the  zone 
number selected. If your entry is not available on the DGM panel, the display will read 
“NOT VALID ENTRY.” 

If the READ button is pressed when several zones are either in Alarm, Trouble, or Out of 
Service, it will cause the next zone to be displayed. This will allow you to quickly advance 
through the list. 

The READ button is also used by some programming functions to view a specific zone, or 
to advance through zones. 

5.2.2  IN/OUT 

After entering a zone number, press the IN/OUT button to toggle the selected zone in or 
out  of  service.  The  display  will  show  the  current  status  of  the  zone,  and  the  panel  will 
transmit the information to the SYSTEM 3505 PRISM LX. You must have the IN & OUT 
OF  SERVICE  option  installed  on  your  DGM  panel.  Otherwise,  it  will  respond  by 
displaying "??????" on the lower line of the display. The operator at the SYSTEM 3505 
PRISM LX also has the ability to place zones on the DGM panels in and out of service. 

When a zone is out of service, future alarm and trouble conditions on that zone will not be 
reported to the SYSTEM 3505 PRISM LX until the zone is restored to service. 

The IN/OUT button is also used by some programming functions as a shortcut to setting a 
parameter on all zones at one time. For example, by using IN/OUT with Function 22 you 
are able to set all zones in the panel to Normally Closed or Normally Open at the same 
time. 

5.2.3  CLR/SIL 

Press  the  CLR/SIL  button  to  clear  any  number  entered  via  the  numeric  keypad,  or  to 
silence the beeper. Upon initialization, push this button to clear the display, and show the 
time and alarm mode. 

As a shortcut, press CLR/SIL twice to display the current RTS value without entering the 
Request to Send Function (11). 

The CLR/SIL button is also used by programming functions to clear the display.  

5.2.4  ENTER 

After  entering  the  password,  press  ENTER  to  allow  access  to  the  programming  mode. 
Once in programming mode, press ENTER to have the DGM program accept information 
entered from the keypad. 

Summary of Contents for DGM-32/64




























































Reviews: