Prepare the Camera
Connect and secure all necessary cables from
the inner box to all desired applications
Connect AC Power Adapter to the camera’s
Inner box. Make sure to connect positive and
negative lines in their corresponding locations.
Power Requirements: AC24V
Power Consumption: Heater Off: 24W, 1000mA,
Heater On: 57W, 2400mA
2
Connect BNC Coaxial cable to camera’s inner box.
Connect other end of the BNC cable to a DVR
or monitor.
4
Mount the Camera
Using the desired Wall or Ceiling Mount, secure camera’s Mounting Box
to wall/ ceiling.
Unscrew the top cover of the mounting box
and remove the protective plastic to expose
the four screw holes
4
Using the mounting box or the mounting template
mark on the wall or ceiling the locations for the
four bolts.
5
Using a drill, drill four holes for the bolts and
secure mounting box to wall/ceiling.
6
Remove PTZ mechanism from the upper housing.
To detach mechanism from upper housing,
press down and hold both black handles marked
‘A’ and ‘B’ on the camera mechanism.
Pull both handles up to detach the camera.
7
2
6
8
DIP Switch Setup
Using the DIP Switch in the inner box, setup the camera’s
Communication Protocol, Joystick Controller, and camera's ID.
ON
J
2
1
3
4
5
6
7
8
AUTO-
Factory Default
1
ON
J
2
1
3
4
5
6
7
8
PELCO-D
2
ON
J
2
1
3
4
5
6
7
8
PELCO-P
3
ON
J
2
1
3
4
5
6
7
8
SAMSUNG
4
ON
J
2
1
3
4
5
6
7
8
PANASONIC
5
ON
J
2
1
3
4
5
6
7
8
GE(Kalatel)
6
ON
J
2
1
3
4
5
6
7
8
AD (American Dynamics)
7
ON
8J
2
1
3
4
5
6
7
8
2400 BPS
1
ON
8J
2
1
3
4
5
6
7
8
4800 BPS
2
ON
8J
2
1
3
4
5
6
7
8
9600 BPS -
Factory Default
3
ON
8J
2
1
3
4
5
6
7
8
19200 BPS
4
38400 BPS
5
ON
8J
2
1
3
4
5
6
7
8
ON
8J
2
1
3
4
5
6
7
8
Communication
Protocol
Bit Rate
RS-485 Termination
Resistor
3
Camera’s ID
Using the bottom D P Switch, setup the
camera’s ID. By default, the camera’s D
is set as 1. Users can select 1~255 IDs
by turning switches ON or OFF.
Each switch has a numerical value. The
camera’s ID = the sum of all switches
that are turned ON.
!
If camera model includes the inner box inside the mounting
box, make sure all cables remain intact during installation
Connect power and initial testing
Connect the camera to the power and make sure it is operating
Properly.
Power Requirements: AC24V
Power Consumption: 24W, 1000mA, Heater On: 57W, 2400mA
When System Initialize screen appear, take note of the camera’s
protocol, Baud Rate and Address. This information will be necessary
to complete camera’s connection to a DVR or Keyboard Joystick.
When setup is complete, Home Position will show OK
!
This order of fastening the screws guarantees optimal
sealing and protects the camera from weather elements
INSTALLATION
INSTALLATION
INSTALLATION
!
Mounting Accessory for the DWC-PTZ37X is sold separately
with the camera’s wiring module. For wiring module in the
dome, see DWC-PTZ37XFM and DWC-PTZ37XAL models.
Thank you for purchasing Digital Watchdog’s Super Speed Dome PTZ Outdoor Dome Camera.
Before installing the camera, please verify your model and read this guide carefully.
20150121
The following items are included with the PTZ camera
Camera Module
Upper Housing
Covering Dome
Inner Box (Found in the upper
housing or mounting box)
Mounting Box (Sold Separately)
Protocol Setup
Baud Rate Setup
RS 485
Termination Resistor
ON
8J
2
1
3
4
5
6
7
8
Inner Box
Pass the cable connector from the inner box
through the upper housing pipe.
f inner box is located in the upper housing,
connect the desired mounting bracket and run
the wires through the bracket.
Screw the upper housing to the mounting box/
bracket. Turn the upper housing at least seven (7)
times to secure a tight connection.
For outdoor installation, wind the weatherproof tape
around the upper housing’s pipe.
9
Hook the safety wire to the safety hook on the
upper housing. Using the safety hanger, secure it
to the mounting box/ bracket.
Plug cable connector from the inner box
to the upper housing.
11
10
8
TEL: (866) 446-3595
www.Digital-Watchdog.com / [email protected]
Technical Support Hours: Monday-Friday 9:00AM to 8:00PM EST
INSTALLATION
1
3
5
7
4
Analog PTZ Dome Camera
Quick Start Guide
x
37
Housing Safety
Cable Hanger
Waterproof Tape
Mounting
Template
Hexagonal Wrench
Anchor Bolt (4pcs)
Safety Wire
PTZ37X QSG
CD (Manual)
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will be required to correct the interference a this own
expense.
To disconnect power from the mains, pull out the mains cord plug.
When install the product, ensure that the plug is easily accessible.
Version 1.01
Connect the RS-485 wires to a terminal box
matching the inner box RS-485 terminals.
Connect the other end of the cable to a terminal
box matching the DVR or keyboard controller’s
RS-485 Terminals.
Make sure the two black handles marked ‘A’
and ‘B’ correspond with the ‘A’ and ‘B’ markings
on the sides of the upper housing.
Note: Before snapping the camera back into
the housing, make sure all cables are
properly secured.
13
Remove protecting gear from the camera’s lens
Connect the cover dome to the upper housing
by securing the safety wire.
15
Snap the camera mechanism back into the upper
housing.
Secure dome to camera by fastening the screws
on the dome in the order shown here.
18
f no adjustments need to be made to the
wiring, place the dome cover on the upper
housing.
17
PREPARATION
INSTALLATION
14
12
AC
Adapter
INSTALLATION
INSTALLATION