DW-ILWLIPM
DW-ILIRIP940
DW-ILIRIP850
Quick Start Guide
Quick Start Guide
Tel: +1 (866) 446-3595 / (813) 888-9555
Technical Support Hours:
9:00AM – 8:00PM EST, Monday through Friday
digital-watchdog.com
Attention:
This document is intended to serve as a quick reference
for the initial setup. It is recommended that the user read the entire
instruction manual for complete and proper installation and usage.
NOTE:
Download all your support materials and tools in one place.
1. Go to:
http://www.digital-watchdog.com/resources.
2. Search for your product by entering the part number
in the
‘Search by Product’
search bar. Results
for applicable part numbers will populate
automatically based on the part number you enter.
3. Click
‘Search’
. All supported materials, including
manuals and quick start guide (QSGs) will
appear in the results.
STEP 1 – INSTALLATION
Optimum results are achieved by setting up at night and
viewing the results on a monitor.
1. Attach the illuminator mount to wall or camera housing
using appropriate hardware.
2. Select a diffuser with an appropriate angle based on your
installation needs. To position the required diffuser sheet,
using the supplied pry tool, insert into the slot located on
the bottom of the lens. Gently lift the cover upwards slowly.
Repeat at opposite end and carefully remove cover. Remove
backing sheet from the two adhesive disc and secure
required diffuser in position. Finally, firmly clip the lens
cover back into place.
3. Adjust the angle of the illuminator to match the cameras
field of view.
4. Adjust the vertical alignment by loosening the side bolts
(one on each side of the main body) to maximize the results.
5. Tilt the lamp downwards until the desired field of view it
illuminated.
DW-ILWLIPM
DW-ILIRIP850
DW-ILIRIP940
WHITE LIGHT AND IR LED ILLUMINATORS
STEP 2 – CABLING THE ILLUMINATOR
Connect to PoE+ switch or PoE+ injector for power and
network connection.
Illuminators are powered by Power over the Ethernet (PoE+)
via a network cable connector to a PoE IEEE802at compliant
switch. The power consumption of the illuminators complies
with PoE+ IEEE802at.
These illuminators are not supplied with a power cord. Instead,
they are supplied with a 3.28ft (1m) long network cable. At the
end of the network cable is a female RJ45 Cat5e compliant jack
with an IP68 rated cover.
Power requirements
Power consumption
PoE+ (IEEE802.3at)
25W
NOTE:
• Only to be installed outside of arms reach.
• Installation should be done by skilled personnel or
under supervision of such personnel.
• The illuminator is PoE+.
• Only to be installed in restricted access areas.
• Terminal block not included. Installation may require
advice from a qualified person.
WHAT’S IN THE BOX
1x Illuminator
1x waterproof cap
1x mount bracket
2x M6 screw and washer sets for bracket
1x allen key
1x front cover opener
1x diffuser pack (30°, 60°, 95°) * 20° and 80° diffusers are available upon request.
1x quick setup guide
To use the illuminator’s water proof wiring:
a. Install the LAN cable into .
b. will be assembled to with a 1/4 turn.
c. Thread tightly to .
a
b
c
a
a
b
b
c
NOTE:
To ensure moisture seal, make sure the o-ring
is in place between and . In extreme
environments use of an outdoor rated sealer is
recommended.
a
b
NOTE:
When using the waterproof cap, crimp the RJ45
connector after passing the cable through the
waterproof cap.
NOTE:
Ensure that the IP68-rated cover is correctly
fitter and attached to the network cable. If this
is not fitter correctly, moisture can get into the
connector and may cause the unit to malfunction.
This would void the warranty on the product.
NOTE:
Illuminator will flash once every second when
insufficient power is applied.
