Digital Watchdog MEGApix PanO DWC-PPVF5Di1TW Quick Start Manual Download Page 1

Page: 1 / 6

Quick Start Guide

Tel: +1 (866) 446-3595 / (813) 888-9555
Technical Support Hours:

9:00 AM – 8:00 PM EST, Monday through Friday

digital-watchdog.com

MEGApix IVA+ models

9MP model

5MP model

DWC-PPVF9Di2TW

DWC-PVF9Di2TW

DWC-PVF5Di1TW

DWC-PPVF5Di1TW

WHAT’S IN THE BOX

Quick Setup and

Download Guides

1 set

Mount Bolts and

Nuts – 2pcs

1 set

Metal Mounting plate

Screws and Plastic

Anchors – 3pcs

1 set

Mounting

Template for Bolt

and Nut

Installation

Waterproof Cap

and Rubber Rings

(Black: ø0.15”

(ø4mm), White:

ø0.19” (ø5mm))

1 set

Mounting

Template for Metal

Plate

Installation

Star Wrench

(T-20)

Pass the wires through and make all the necessary connections.
1. If you are using a PoE switch, connect the camera using an Ethernet

cable for both data and power.

2. If you are using a non-PoE switch, connect the camera to the switch

using an Ethernet cable for data transmission and use a power adapter
to power the camera.

STEP 2 – POWERING THE CAMERA

Model

Power Requirements

Power Consumption

DWC-PPVF9Di2TW

DWC-PVF9Di2TW

DC12V, PoE IEEE

802.3af Class 3.

(Adapter not

included)

DC12V: max 8.5W

PoE: max 10W

DWC-PPVF5Di1TW

DWC-PVF5Di1TW

DC12V: max 7.5W

PoE: max 8.7W

1. The mounting surface must bear five times the weight of your camera.
2. Do not let the cables get caught in improper places or the electric line

cover to be damaged. This may cause a breakdown or fire.

3. CAUTION: These servicing instructions are for use by qualified service

personnel only. To reduce the risk of electric shock do not perform any
servicing other than that contained in the operating instructions unless
you are qualified to do so.

4. CAUTION: There is a risk of explosion if the battery is replaced

incorrectly and it should be replaced only with the same battery.
ATTENTION: Il y a risque d’explosion si la batterie est remplacée par
une batterie de type incorrect. Mettre au rebut les batteries usages
conformément aux instructions.

5. Used batteries must be disposed of according to local regulations or

the battery manufacturer’s instructions. Disposing of batteries in a fire
or in a hot oven, or mechanically crushing and cutting them may cause
an explosion.

6. Leaving the battery in very high temperature or low air pressure

environments may result in an explosion or leak of flammable liquids
or gases.

7. This product is intended to be supplied by a UL Listed Power Supply

Unit marked “Class 2” or “LPS” or “PS2” and rated 12 Vdc, 0.71A (DWC-
PPVF9Di2TW and DWC-PVF9Di2TW) and 0.63A (DWC-PPVF5Di1TW
and DWC-PVF5Di1TW) min.

The wired LAN hub providing power over the Ethernet (PoE) in
accordance with IEEE 802-3af shall be a UL Listed device with the
output evaluated as a Limited Power Source as defined in UL60950-1
or PS2 as defined in UL62368-1.

9. Unit is intended for installation in a Network Environment 0 as defined

in IEC TR 62102. As such, associated Ethernet wiring shall be limited to
inside the building.

10. Using the mounting template sheet or the camera itself, mark and drill

the necessary holes in the wall or ceiling.

STEP 1 – PREPARING TO MOUNT THE CAMERA

Attention:

This document is intended to serve as a quick reference for the

initial setup. It is recommended that the user read the entire instruction manual

for complete and proper installation and usage.

NOTE:

Download all your support materials and tools in one place

1. Go to:

http://www.digital-watchdog.com/resources

2. Search your product by entering the part number in the

‘Search by Product’

search bar. Results for applicable

part numbers will populate automatically based on the

part number you enter.

3. Click

‘Search’

. All supported materials, including manuals

and quick start guide (QSGs) will appear in the results.

Resetting the camera:

To reset the camera,

use the tip of a paper clip or a pencil and
press the reset button. Pressing the
button for five (5) seconds will initiate a
camera-wide reset of all the settings,
including network settings.

Default Login Information: admin | admin

When logging into the camera for the first time, you will be prompted

to set up a new password. You can set the new password using the

DW® IP Finder™ software or directly from the camera’s browser menu.

Installation using mount bolt and screws:

1. Using the template sheet for the nuts and bolts installation, mark and

drill the holes on the mounting surface.

2. Secure the two long mounting screws to the camera’s base.
3. Pass the wires through the mount bracket and make all necessary

connections.

4. Mount the camera to the mounting surface by using the 2 mounting

nuts. Rotate the locking discs over the screws until the camera is held
tightly from the mounting surface.

5. Re-attach the camera’s gasket ring and dome to the camera module by

aligning the screw holes. Be sure to align the wedge on the side of the
camera with the one on the mounting bracket.

1. Once all cables are connected, secure the camera to the mounting

surface using the included screws.

2. For soft installation surfaces, use the included metal mount plate. Fix

the mounting plate on the mounting surface using the
included screws. Then, press the bottom case onto
the mounting plate. The three bezels on the case will
align and snap lock onto the plate.

STEP 3 – INSTALLING THE CAMERA

4. Re-attach the camera’s gasket ring and dome

to the camera module by aligning the screw
holes. Align the wedge on the side of the
camera with the one on the mounting bracket.

a.   Pass the LAN cable through the waterproof cap, gasket and the rubber ring.
b.   Connect the LAN cable to the camera’s network port .
c. will be affixed to with a ¼ turn counter-clockwise.
d.   Thread and twist tightly to .

3. The waterproof cap set comes with two rubber rings with different diameters.

The black rubber ring has an internal diameter of ø0.15” (ø4mm). The white

rubber ring has an internal diameter of ø0.19” (ø5mm). When using the

waterproof cap, use the rubber ring best suited for your network cable’s diameter.

NOTE:

To ensure moisture seal, make sure the o-ring is in place

between

and

. In extreme environments use of an

outdoor rated sealer is recommended.

NOTE:

Cables with ø4.5mm to ø5.5mm thickness should use the

black rubber ring. Cables over ø5.5mm in thickness should

use the white rubber ring.