Default Login Information
Username:
admin
Password:
admin
Quick Start Guide
Quick Start Guide
WHAT’S IN THE BOX
Quick setup
and
Installation
Guides
1 set
Tapping
Screws –
4pcs
1 set
Mounting
Template
1
Plastic Plugs
– 4pcs
1 set
Waterproof
Cap
1 set
Rubber Plug
1
Hexagonal
Wrench 0.11”
(3mm)
1
DWC-MV95Wi28TW
DWC-MV95Wi36TW
STEP 1 – PREPARING TO MOUNT THE CAMERA
STEP 2 – POWERING THE CAMERA
Power requirements
Power consumption
DC12V, PoE
(IEEE 802.3af class 3).
Adapter not Included.
<6W
1. The mounting surface must bear five times the weight of your camera.
2. Do not let the cables get caught in improper places or the electric line
cover to be damaged. This may cause a breakdown or fire.
3. For the installation process, remove the dome cover from the
camera base using the included wrench.
4. Using the mounting template sheet or the camera itself, mark and
drill the necessary holes in the wall or ceiling.
Pass the wires through and make all the necessary connections. See
STEP 4 for more information.
1. NETWORK CONNECTIONS – Using a PoE Switch or
PoE Injector, connect the camera using an Ethernet
cable for both data and power.
2. NETWORK CONNECTIONS – Not using PoE Switch or
PoE Injector, connect the camera to the switch using an
Ethernet cable for data transmission and use a power
adapter to power the camera.
Resetting the camera:
To reset the camera, use the tip of a
paper clip or a pencil and press the reset button at the base of
the camera. Pressing the button
for five (5) seconds will
initiate a camera-wide
reset of all the settings,
including network settings.
Tel: +1 (866) 446-3595 / (813) 888-9555
Technical Support Hours:
9:00 AM – 8:00 PM EST, Monday through Friday
digital-watchdog.com
Attention:
This document is intended to serve as a quick reference for initial
set-up. It is recommended that the user read the entire instruction manual for
complete and proper installation and usage.
NOTE:
Download all your support materials and tools in one place
1. Go to:
http://www.digital-watchdog.com/resources
2. Search your product by entering the part number in the
‘Search by Product’
search bar. Results for applicable
part numbers will populate automatically based on the
part number you enter.
3. Click
‘Search’
. All supported materials, including manuals
and quick start guide (QSGs) will appear in the results.
a
b
c
STEP 3 – INSTALLING THE CAMERA
1. Mount the camera to the mounting surface using the included screws
and anchors.
2. To use the camera’s waterproof wiring:
a. Install the LAN cable into .
b. will be assembled
to with a 1/4 turn.
c. Thread tightly to .
3. Adjust the camera’s tilt and angle.
a. Pan and rotation: 0 ~ 355°
b. Tilt: 0 ~ 67°
4. Place the dome cover on the camera using the wrench to tighten the
screws on the dome.
a
a
b
b
c
STEP 4 – CABLING
STEP 5 – MANAGING THE SD CARD
Use the diagram below to properly connect power, network, alarm input
and outputs and audio to the camera.
1. To install the camera’s SD Card, locate the SD card slot at the base of
the camera module.
2. Insert a class 10 SD/SDHC/SDXC card into the SD card slot by
pressing the SD card until clicks.
3. To remove the SD card, press the card inward until it clicks to release
it from the card slot.
Power
Network
Audio Input
Alarm Input/Output
AL
AR
M
1
2
3
4
1
COM
2
OPEN
3
INA
4
GND
Rubber Plug