DWC-MD72Di28T
STEP 1 - PREPARING TO MOUNT THE CAMERA
STEP 3 - INSTALLING THE CAMERA
STEP 2 - POWERING THE CAMERA
1. The mounting surface must withstand five times the camera weight.
2. Do not let the cables get caught in improper places or the electric line cover can be damaged. This
may cause a short or fire.
3. CAUTION: These servicing instructions are for use by qualified service personnel only. To reduce
the risk of electric shock do not perform any servicing other than that contained in the operating
instructions unless you are qualified to do so.
4. This product is intended to be supplied by a UL Listed Power Supply Unit marked “Class 2” or “LPS”
or “PS2” and rated 12 Vdc, 0.32A min.
5. The wired LAN hub providing power over the Ethernet (PoE) in accordance with IEEE 802-3af shall
be a UL Listed device with the output evaluated as a Limited Power Source as defined in UL60950-1
or PS2 as defined in UL62368-1.
1. Secure the camera to the mounting surface using the included screws
and anchors.
2. Adjust the camera’s pan, tilt and position to achieve the desired view.
The cameras’ max angles are:
Pan: 0° ~ 335°
Tilt: 0° ~ 70°
Rotation: 0° ~ 360°
Pass the wires through the mount bracket and make all necessary connections.
1. NETWORK CONNECTIONS - If you are using a PoE switch, connect the camera using an
Ethernet cable for both data and power.
2. NETWORK CONNECTIONS - If you are using a non-PoE switch, connect the camera to
the switch using an Ethernet cable for data transmission and use a power adapter to
power the camera.
Power requirements
Power consumption
DC 12V, PoE (IEEE 802.3af Class 2)
Adapter not included.
DC12V: max 3.8W
PoE: max 5.5W
Quick Start Guide
Quick Start Guide
Resetting the camera:
To reset the camera’s settings, including the
network settings, use the tip of a paper clip or a pencil. Press the
reset button for five (5) seconds.
Reset Button
Protective
Ring
WHAT’S IN THE BOX
Quick Setup
and
Installation
Guides
1 set
Mounting
Template
1
Screws and
Plastic
Anchors –
3pcs
1 set
Tel: +1 (866) 446-3595 / (813) 888-9555
Technical Support Hours:
9:00 AM – 8:00 PM EST, Monday through Friday
digital-watchdog.com
Attention:
This document is intended to serve as a quick reference for the initial
set-up. It is recommended that the user read the entire instruction manual for
complete and proper installation and usage.
NOTE:
Download all your support materials and tools in one place
1. Go to:
http://www.digital-watchdog.com/resources
2. Search your product by entering the part number in the
‘Search by Product’
search bar. Results for applicable
part numbers will populate automatically based on the
part number you enter.
3. Click
‘Search’
. All supported materials, including manuals
and quick start guide (QSGs) will appear in the results.
Mounting Template
Default Login Information: admin | admin
When logging into the camera for the first time, you will be prompted
to set up a new password. You can set the new password using the
DW® IP Finder™ software or directly from the camera’s browser menu.
6. Unit is intended for installation in a Network Environment 0 as defined
in IEC TR 62102. As such, associated Ethernet wiring shall be limited to
inside the building.
7. For the installation process, remove the dome cover from the camera
module. Insert a coin or a screwdriver between the camera’s base and
the dome. Twist the coin to pry the dome cover open.
8. Before installing the camera, be sure to remove the protective ring from
the camera’s lens module.
9. Using the mounting template or the camera itself, mark and drill the
necessary holes in the mounting surface.