Digital Watchdog MEGApix DWC-MB44WiA Quick Start Manual Download Page 1

Page: 1 / 7

Quick Start Guide

Tel: +1 (866) 446-3595 / (813) 888-9555
Technical Support Hours:

9:00AM – 8:00PM EST, Monday thru Friday

digital-watchdog.com

Attention:

This document is intended to serve as a quick reference for initial

set-up. It is recommended that the user read the entire instruction manual for

complete and proper installation and usage.

NOTE:

Download all your support materials and tools in one place

1. Go to:

http://www.digital-watchdog.com/resources

2. Search your product by entering the part number in the

‘Search by Product’

search bar. Results for applicable

part numbers will populate automatically based on the

part number you enter.

3. Click

‘Search’

. All supported materials, including manuals

and quick start guide (QSGs) will appear in the results.

STEP 1 – PREPARING TO MOUNT THE CAMERA

STEP 2 – CABLING THE CAMERA TO

EXTERNAL DEVICES

Pass the wires through and make all necessary connections.

1. NETWORK CONNECTIONS – Using a PoE Switch or PoE Injector,

connect the camera using an Ethernet cable for both data and
power.

2. NETWORK CONNECTIONS – Not using PoE Switch or PoE

Injector, connect the camera to the switch using an Ethernet
cable for data transmission and use a power adapter to power the
camera.

Power requirements

Power consumption

DC12V, PoE

(IEEE 802.3af class 3).

Adapter not Included.

DC12V: Max 11W

PoE: Max 12.9W

Resetting the camera:

To reset the camera, use the tip of a

paper clip or a pencil and press the reset button. Pressing the
button for five (5) seconds will initiate a camera-wide reset of
all the settings, including network settings.

1. The mounting surface must bear five times the weight of

your camera.

2. Do not let the cables get caught in improper places or the electric

line cover to be damaged. This may cause a breakdown or fire.

3. CAUTION: These servicing instructions are for use by qualified

service personnel only. To reduce the risk of electric shock do not
perform any servicing other than that contained in the operating
instructions unless you are qualified to do so.

4. This product is intended to be supplied by a UL Listed Power

Supply Unit marked “Class 2” or “LPS” or “PS2” and rated 12 Vdc,
920 mA min.

5. The wired LAN hub providing power over the Ethernet (PoE) in

accordance with IEEE 802-3af shall be a UL Listed device with
the output evaluated as a Limited Power Source as defined in
UL60950-1 or PS2 as defined in UL62368-1.

6. Unit is intended for installation in a Network Environment 0 as

defined in IEC TR 62102. As such, associated Ethernet wiring shall
be limited to inside the building.

7. Using the mounting template sheet or the camera itself, mark and

drill the necessary holes in the wall or ceiling.

DWC-MB44WiA

Default Login Information

Username:

admin

Password:

admin

Test Video

Output

Reset Button

WHAT’S IN THE BOX

Quick setup

guide

Screws and

plastic

anchors – 4pcs

1 Set

Mounting

template

Torque wrench

Test video

cable

DC plug cable

Waterproof

cap

1 Set

1. Once all cables are connected, secure the camera to the mounting

surface using the included screws.

2. Loosen the pan and tilt screws at the base of the camera’s bracket

to adjust the camera’s view and position.

3. To use the camera’s water proof wiring:

a.    Install the LAN cable into .
b.      will be assembled to with a 1/4 turn.
c.    Thread tightly to .

3. Loosen the pan and tilt screws at the base of the camera’s bracket

to adjust the camera’s view and position.

STEP 3 – INSTALLING THE CAMERA

NOTE:

To ensure moisture seal, make sure the o-ring is in place

between and . In extreme environments use of an
outdoor rated sealer is recommended.

NOTE:

When using the waterproof cap, crimp the RJ45

connector after passing the cable through the
waterproof cap.