Lens Specifications
If you are using an automatic iris lens with the camera, the lens has
to be connected to the A-Iris socket of the camera. If you are using
a lens with manual or fixed iris, this socket is not used.
Operation of the camera will be confirmed by the power LED at the
rear side of the camera.
MC421D
IP 2.1MP Color Box Camera
Quick Setup Guide
Prepare the Camera and Mounting Surface
SPECIFICATIONS
Network Connection
There are two options.*
Using a Non-PoE Switch
!
Frequent use may cause a System Error
Using a PoE-Enabled Switch
The MEGAPIX Camera is PoE-compliant, allowing transmission of power and data via a single
ethernet cable. Follow the illustrations below to connect the camera to a PoE-enabled switch using
an ethernet cable.
If a PoE-enabled switch is not used, use a power adaptor to connect the MEGAPIX Camera to a
Non-PoE switch.
Use the camera’s Mounting accessory
to mark drilling holes on the mounting
surface.
Attach the box camera to the mounting
bracket & adjust the camera’s position.
Consult the mounting bracket’s manual for
additional information.
3
Drill holes into the drywall and mount the
camera’s mount.
4
Mount the Camera
The MEGAPIX Camera is designed to be surface mounted on a wall
or ceiling.
Locate the SD card slot in the back of the camera
module. Insert the SD card in the slot and push it
down, until you hear a ‘click’ sound. See page 16
in this QSG for more information on setting up an
emergency recording schedule.
6
Connect the RJ45 to a CAT5 cable or a
power adaptor. If necessary, connect the
Audio In and Out, and Relay Control cables.
Check the LED light. Green light flickers for
booting. Red light turns on when booting is
complete.
7
2
6
8
Adjust the lens’ zoom and focus accordingly.
Consult the manual for the lens for more
information.
8
Additional Cabling Connections
Resetting the Camera
Pressing the reset button on the camera’s control board for five (5) seconds will initialize all environmental
variables to factory default. Previous setup for IP default, time, etcetera will be deleted. If a system IP address is
lost, reset the camera back to factory default.The following are the default network settings:
IP Mode
DHCP
IP Address
192.168.1.123
Subnet Mask
255.255.255.0
Gateway
192.168.1.123
Command Port
7000
HTTP Port
80
Live Port
7001
Power
Audio In/ Out
RJ45 Connector
DC Driven (DC)
1.control -
2.c
3.drive +
4.GND
1
2
3
4
A-IRIS
CS-Mount lens
C-Mount lens
Adapter Ring
After removing the protecting cap,
attach the lens into the camera by
turning clockwise.
1. Attach the C-Mount lens adapter by turning clockwise.
2. Attach the lens to the camera by turning clockwise.
C-Mount Lens : 10mm or less
CS-Mount Lens : 5mm or less
NOTE
!
DC12V
AUDIO
ETHERNET / PoE
RS485
PWR
/AC24V
+ -
IN/OUT
+
-
+
-
RALAY OUT
SENSOR IN
RESET
VIDEO OUT
MICRO SD
DC12V
AUDIO
ETHERNET / PoE
RS485
PWR
/AC24V
+ -
IN/OUT
+
-
+
-
RELAY OUT
SENSOR IN
RESET
VIDEO OUT
MICRO SD
Thank you for purchasing Digital Watchdog’s Snapit MEAPIX lndoor Dome Camera.
Before installing the camera, please verify your model and read this guide carefully.
02222013
The following items are included with the MV421D/TIR camera
TROX-T20
L-Wrench
Color Box IP
Camera
PREPARATION
TEL: (866) 446-4359
www.Digital-Watchdog.com / [email protected]
Technical Support Hours: Monday-Friday 8:30AM to 8:00PM EST
INSTALLATION
Quick Start
Guide
2 Port
Terminal Block
CS Lens
Mount Adapter
CD
(Manual &
Software)
1
2
1
Attach an appropriate Lens to the camera.
See page 7 in this QSG for more information.
2
3
5
7
4
Camera Specifications
Second Video
Jack
AUDIO
NETWORK
OPERATIONAL
ENVIRONMENTAL
Storage Temperature
-20
o
C ~ 70
o
C (-4
o
F ~ 158
o
F)
IMAGE
Image Sensor
1/2.8” Sony CMOS Sensor
Total Pixels
2016 (H) X 1108 (V)
Minimum Scene Illumination F1.6 (30IRE): 0.5 Lux [Color]
F1.6 (30IRE): 0.01 Lux [B&W]
Frame Rate
Up to 30fps at All Resolutions
Video Compression Type
H.264, MPEG4, MJPEG (Super Fine~Low)
IP
IPv4, IPv6
Protocol
TCP/IP, HTTP, DHCP, PPPoE, ICMP, ARP, RARP,
RTSP, NTP, UDP, Multicast
LAN
802.3 Compliance 10/100 LAN
Web Viewer
OS: Windows XP / Vista / 7, MAC OS
Browser: Internet Explorer, Chrome, Firefox, Safari
Video Management Software
DW Spectrum/ NxMS/ Pivot
ONVIF Conformance
Yes
Streaming Capability
Dual-Stream at Different Rates and Resolutions
Power Requirement
DC 12V, PoE (IEEE802.3af Class 2)
Power Consumption
6.5W, 550mA
Operating Humidity
Less than 90% (Non-Condensing)
Operating Temperature/ Humidity
-10
o
C ~ 50
o
C (14
o
F ~ 122
o
F)
Other Certifications
CE, FCC, RoHS
Memory Slot
24 hours recording to Micro SDHC Card (4GB-32GB)
Card Not Included*
Dimensions
131.3 X 55 mm (5.2 X 2.17 in)
Material
Aluminum Housing
Weight
0.55 lbs
Sensor In/ Out
1 Input/ 1 Output Built-In
Mirror & Flip
Off, On
Maximum User Access
5 Users
Day and Night
Auto, Day (Color), Night (B/W)
MECHANICAL
ELECTRICAL
Brightness
0~20
DNR (Digital Noise Reduction)
Off/ Low/ Middle/ High
Auto Gain Control
0~20
Digital Slow Shutter
Off, 2X, 3X, 4X
Shutter Mode
Auto, Manual
WDR (Wide Dynamic Range)
Off, On, Level 0~9
BLC (Backlight Compensation)
Off, On
Chroma (Hue & Saturation Settings)
0~20
Lens Mode
Manual, DC
Sharpness
0~10
Resolution
1920X1080 (16:9) ~ 320X240 (4:3)
Alarm Notifications
Notifications Via E-mail
Compression and Sampling Rate
G.711 (8KHz)
Input / Output
1 Line In and 1 Line Out Mono