manualshive.com logo in svg

Digital Projection E-Vision Laser 15000 Series, Installation & Quick Start Manual

Share
Download
Digital Projection E-Vision Laser 15000 Series Installation & Quick Start Manual Download Page 25

Power Supply

Digital Projection E-Vision Laser 15000 Series

Power Supply

AC Power Precautions

Warning! Death or Serious Injury could occur if the following precautions are ignored

Shock Hazard! Only use the AC power cord provided or recommended by the manufacturer

Fire & Shock Hazard! Do not operate the product unless the power cord, socket and plug meet local rating standards

Do not attempt operation if the AC supply is not within the specified parameters

The AC power cord must be inserted into a socket with grounding

Disconnect the product from the AC supply before installing, moving, servicing, cleaning or removing covers

Do not use an AC power cord that appears damaged

Do not overload power sockets or extension cords

Installation & QuickStart Guide

Rev B April 2021

page 25

Notes

Summary of Contents for E-Vision Laser 15000 Series


















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands