manualshive.com logo in svg

Digital ID View Real-time NETWORK VIDEO RECORDER, User Manual

Share
Download
Digital ID View Real-time NETWORK VIDEO RECORDER User Manual Download Page 12

12 

 

 

1.5   

      Remote Control (Optional) 

   

     

The NVR can be operated through the remote controller. The remote control operation 

is showing in below figure. Batteries (2xAAA) must be installed before operating.   

 

 

 

 

 

 

 

 

 

1.

 

ID

 Button: 

Press ID  number key to 

switch to the NVR that user would like to control.   

Press a number between 1 and 9 corresponding to 

the unit ID user wish to control. The user ID must 

be set in the device before operating.   

2.

 

Export Button:

 Enable/disable Export menu.   

3.

 

F1/F2 Button:

 Reserved. 

4.

 

ACK Button:

 Alarm acknowledged. 

5.

 

Alphanumeric Buttons

 

6.

 

Display Button: 

Press to switch the display mode. 

7.

 

Sequence Button:

 Press to enable/disable 

sequence display mode. 

8.

 

Zoom Button: 

For digital zoom in/out operation 

under digital zoom mode. Or for zoom in/out 

control under PTZ mode. 

9.

 

Focus Button:

 For focus control under PTZ mode. 

10.

 

PTZ Button:

 To enable/disable PTZ control 

menu. 

11.

 

Direction/Enter Button:

 The Direction buttons 

are used to navigate the focus display windows or 

select items in the menu. The Enter button is used 

to confirm the selection. 

12.

 

Search Button

: To enable/disable playback mode.   

13.

 

Menu Button

: To enable/disable configuration 

menu. 

14.

 

Playback Control Buttons: S

ame as playback 

operation on playback mode. 

15.

 

PTZ control Buttons: 

Same as PTZ control 

operation on PTZ mode. 

Summary of Contents for Real-time NETWORK VIDEO RECORDER




















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands