manualshive.com logo in svg

Digital Equipment Alpha 21164PC, Hardware Reference Manual, Page: 83 / 372

Share
Download
Digital Equipment Alpha 21164PC Hardware Reference Manual Download Page 83

29 September 1997 – Subject To Change

Hardware Interface

3–11

21164PC Signal Names and Functions

irq_h<3:0>

I

4

System interrupt requests. These signals have multiple modes 
of operation. During normal operation, these level-sensitive 
signals are used to signal interrupt requests. During initializa-
tion, these signals are used to set up the CPU cycle time divi-
sor for sys_clk_out1_h as follows:

lw_parity_h<3:0>

B

4

Longword parity. These signals set even INT4 parity for the 
current data cycle. Refer to Section 4.12.1 for information on 
the purpose of each lw_parity_h bit.

mch_hlt_irq_h

I

1

Machine halt interrupt request. This signal has multiple modes 
of operation. During initialization, this signal is used to set up 
sys_clk_out2_ h delay (see Table 4–3). During normal opera-
tion, it is used to signal a halt request.

osc_clk_in_h
osc_clk_in_l

I
I

1
1

Oscillator clock inputs. These signals provide the differential 
clock input that is the fundamental timing of the 21164PC. 
These signals are driven at the same frequency as the internal 
clock frequency (clk_mode_h<1:0> = 01).

port_mode_h<1:0>

I

2

Select test port interface modes (normal, manufacturing, and 
debug). For normal operation, both signals must be deasserted.

Table 3–1 21164PC Signal Descriptions

(Sheet 8 of 10)

Signal

Type Count Description

irq_h<3> irq_h<2> irq_h<1> irq_h<0>

Ratio

Low

High

Low

Low

4

Low

High

Low

High

5

Low

High

High

Low

6

Low

High

High

High

7

High

Low

Low

Low

8

High

Low

Low

High

9

High

Low

High

Low

10

High

Low

High

High

11

High

High

Low

Low

12

High

High

Low

High

13

High

High

High

Low

14

High

High

High

High

15

Summary of Contents for Alpha 21164PC





















































































































































































































































































































































































Reviews:

No comments