background image

 

DigiPoS Millennium Technical Manual

 

Introduction 

 

Congratulations on the purchase of your DigiPoS Retail System!  

You are now the owner of a state-of-the-art DigiPoS Retail System. The DigiPoS Retail 
System is a solution that offers enhanced features, speed and performance combined with 
exceptional reliability. It is also a PC that is unrivalled by other conventional Pentium 
based PCs within the EPoS industry. 

 

Key Features 

 

Component Description 

CPU 

Supports Socket 370 Intel Celeron / PIII/VIA Cyrix C3 CPUs 

CPU CLOCK 

266 MHz to 1GHz 

MAIN MEMORY 

Notebook SO-DIMM X 1 up to 512MB (SDRAM or EDO) 

BIOS 

Enhanced ACPI 1.0 / PnP / APM / DMI / ESCD / PCI bus 2.1 / OnNow /  
DRAM ECC Quick Boot / HW Monitor (LDCM) / I-O Pre-set IRQ / Spread 
Spectrum / PC98 compliant 

CACHE MEMORY 

 

512KB P.B. SRAM 

EXPANSION SLOTS 

Riser Card with 3 FREE Slots: 
1 x ISA, 2 x PCI and 1 x IDE2 CD-ROM connector 

SERIAL PORTS 

COM1, COM2, COM3, COM4 (COM3/4 output on riser card). 
IRQ & I/O address selection by BIOS (Jumper less).

 

PARALLEL PORT 

One LPT port (SPP / EPP / ECP) IRQ and address selectable by BIOS 

USB 

TWO USB ports supporting Windows 95/98/Me/2000/Xp 

FDD 

1.44MB / 3.5" FDD x 1 

ENHANCED PCI IDE 

On board PCI Bus Master IDE1/2 controller with Windows utility. 
Supports Ultra DMA/66 

AGP GRAPHICS 
ADAPTER 

VIA 8604 AGP with shared memory from 2MB up to 32MB. 
Features include: 
Support for 4X AGP VGA controller 
Support for 3D / 2D Graphics Accelerator 
Support for DVD Video Accelerator 
Support for VESA DPMS VGA Monitor for Power Management 
Direct X, VPE, MPEG2 
NT4.0 / 5.0, Windows95/98/Me/2000/Xp utility 
APM / ACPI 1.0 
Supports VESA DPMS VGA monitor for power management 
PC98 compliant 
CRT and LCD TMDS output (Optional) 
Supports dual monitor output (optional) under Windows 98/Me/2000/Xp 

ONBOARD LAN 
(10/100Mbs 
Auto sensing) 

ACPI / NT4.0 / 5.0 (NDIS 5) 
NT 4.0 / Win95/98 utility 
Remote boot ROM  
NT4.0/Win95/98 Utility 
PC98 compliant 
Enable or disable by BIOS set-up 

(Jumper less)

 

ONBOARD AUDIO 

AC97 CODEC on board 

DISK ON CHIP 

With DigiPoS EPoS Diagnostics Utility 

Page 9 of 81 

Summary of Contents for Millennium Socket 370 Series


















































































Reviews: