5.
Fit the Annunciator’s wires through section “A” and then loop them through
the cut-out section of the keypad’s back plate labelled “E” (Figure 2).
6.
Connect the Annunciator’s wires to the keypad’s corresp, –, GRN
and YEL network terminals.
7.
Tighten terminal screws.
8.
Join the keypad’s body plates together.
9.
Insert the Annunciator’s back plate on top of the keypad, using the guide clip
to set the position.
10. Adjust any loose wiring between the Annunciator and the keypad.
11. Insert screws into slots labelled “C” (Figure 2) to set the back cover.
12. Insert screws into slots labelled “D” (Figure 2) and tighten all screws.
13. Join the Annunciator’s body plates together.
14. Program the Annunciator using any keypad on the network.
15. Affix appropriate label to match the display mode (see “Section [003]” on
page 1).
Mounting as a Stand-alone Module
1.
Connect one end of the wires to the Annunciator’s network terminals. Do not
close the back and front covers until you have decided how you will set the
module.
2.
Loop the cable through the space of the Annunciator’s back cover. Place
and hold the Annunciator’s back plate to wall. Remove the guide clip if
desired.
3.
Insert screws into slots labelled “C” (Figure 2) to set the back cover.
4.
Insert screws into slots labelled “D” (Figure 2) and tighten all screws.
5.
Join the body plates together.
6.
Connect the Annunciator’s wires to the control panel ‘s corresp, –,
GRN, and YEL network terminals.
7.
Program the Annunciator using any keypad on the network.
8.
Affix appropriate label to match the display mode (see “Section [003]” on
page 1).
Module Stacking
1.
Install Module 1 (see Figure 3) as you would for either a stand-alone or
mounted installation as described in the previous section.
2.
Separate Module 1’s body plates. Leave back plate mounted to wall.
3.
Cut out space “B” from Module 1’s back plate.
4.
Separate Module 2’s body plates, and connect one end of the wires to its
network terminals.
5.
Loosen Module 1’s network terminal screws without disconnecting wires.
6.
Loop Module 2’s wires through the open gap at the top of Module 1’s back
plate (space B in Figure 1).
7.
Connect Module 2’s wires to Module 1’s network terminals (Figure 3).
8.
Tighten terminal screws.
9.
Join Module 1’s body plates together.
10. Insert Module 2’s back plate on top of Module 1, using the guide clip to set
the position.
11. Adjust any loose wiring between Module 1 and 2.
12. Insert screws into slots labelled “C” (Figure 2) to set the back cover.
13. Insert screws into slots labelled “D” (Figure 2) and tighten all screws.
14. Join Module 2’s body plates together.
15. Program Module 2 using any keypad on the network.
16. Affix appropriate label to match the display mode (see “Section [003]” on
page 1).
17. Repeat steps 1 to 15 where Module 1 and 2 will be Module 2 and 3 (see
Figure 3).
Figure 1 : Cut-out Spaces
Use a knife to cut away two squares approx. 75mm from the
Annunciator’s back plate. Cut a square in front of the guide clip (space A) and at
the top of the rim (space B). Dotted lines indicate cutting lines.
Remove space “B” from any Annunciator that will have additional
modules stacked on top of it as shown in Figure 3. Uppermost
Annunciators such as Module 3 or stand-alone modules do not require
the removal of space “B”.
Figure 2 : Mounting
Figure 3 : Stacking
Warranty
For complete warranty information on this product please refer to the Limited Warranty Statement
found on the website www.paradox.com/terms. Your use of the Paradox product signifies your accep-
tance of all warranty terms and conditions.
Digiplex, Digiplex EVO, and Winload are trademarks or registered trademarks of Paradox Security
Systems Ltd. and its affiliates in Canada, the United States and other countries. All rights reserved.
Specifications may change without prior notice. One or more of the following patents may apply:
7046142, 6215399, 6111256, 6104319, 5920259, 5886632, 5721542, 5287111, 5119069, 5077549.
Canadian and international patents may also apply.
© 2002-2007 Paradox Security Systems Ltd.
A
B
A
75mm
75mm
B
paradox.com
Printed in Canada 07/2007 DGP2ANC1-EI02
