manualshive.com logo in svg

DigiDesign SYNC HD, Manual

Share
Download
DigiDesign SYNC HD Manual Download Page 7

Chapter 1: Introduction

1

chapter 1

Introduction

Welcome to the Digidesign SYNC HD, a multi-
purpose synchronization peripheral for 
Pro Tools HD systems. The SYNC HD supports 
all Pro Tools sample rates, and synchronizes to 
most major time code and clock reference stan-
dards used in audio, video, film, and multime-
dia production. 

The SYNC HD can also be used as a standalone 
synchronization device.

SYNC HD with Pro Tools|HD Systems

With a Pro Tools|HD system, the SYNC HD pro-
vides highly accurate lock to time code. Most 
SYNC HD settings are available directly from 
within Pro Tools.

SYNC HD in Standalone Mode

The SYNC HD can be used as a standalone syn-
chronization converter, time code generator, 
clock generator and time code character genera-
tor. Throughout this guide, the term 

standalone

 

refers to systems using the SYNC HD but 

not

 us-

ing Pro Tools. When used as a standalone device 
(known as “Standalone mode”), the SYNC HD is 
connected to time code or clock signals, and is 
configured from the front panel.

Optionally, while in Standalone mode, the 
SYNC HD can be controlled remotely from a 
Windows computer using the SYNC Setup 
software utility.

SYNC Setup Software Utility

(Windows Only)

The SYNC Setup software utility can be used 
with or without Pro Tools to control all 
SYNC HD features from any supported Win-
dows computer.

Summary of Contents for SYNC HD








































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands