manualshive.com logo in svg

DigiDesign SYNC HD, Manual

Share
Download
DigiDesign SYNC HD Manual Download Page 18

SYNC HD Guide

12

Connecting MIDI 

The SYNC HD MTC Out port supplies MIDI time 
code, derived from conversion (from LTC, VITC 
or Bi-Phase) or from MTC generation, to syn-
chronize MTC-compatible consoles, sequencers, 
lighting systems, and other devices. 

MIDI time code from the MTC Out always 
matches the time code address displayed on the 
SYNC HD front panel. To supply MTC from the 
SYNC HD to another MTC-compatible device, 
connect the device as described below. 

To connect an MTC-compatible device to receive 
MTC from the SYNC HD:

„

Connect the SYNC HD MTC Out port to the 

appropriate MIDI input on the device using a 
standard MIDI cable. 

Pro Tools and MTC

Pro Tools receives MTC from the SYNC HD 
through its connection to the SYNC HD Host 
Serial port. This signal does not include standard 
MIDI time code, but is instead a high-quality, 
proprietary time code signal designed for 
Pro Tools. A MIDI Interface is not required for 
Pro Tools to receive MTC. 

MTC is output constantly whenever the 
SYNC HD is generating time code. This output 
can be muted when time code (LTC) is idle. See 
“MTC Output and Idle Muting” on page 56 for 
details. 

Software Installation 

The following sections provide instructions to 
install software required to use the SYNC HD 
with Pro Tools HD or with the stand alone 
SYNC Setup software (Windows only). 

Pro Tools HD

All software required to use SYNC HD options is 
installed with Pro Tools HD software. 

Updating SYNC HD Firmware

You can update SYNC HD firmware from the 
DigiTest application.

To update SYNC HD firmware:

1  

Confirm that the SYNC HD is properly con-

nected to your computer in one of the following 
ways:

• If it is connected to a Pro Tools system, it 

should be connected to a DigiSerial Port on 
an HD Core card.

• (Windows Only) If it is connected to a com-

puter without Pro Tools, it should be con-
nected to the COM 1 port on the computer 
with a standard serial cable.

2  

Ensure that Pro Tools is not running.

3  

Launch the DigiTest application.

The availability of SYNC HD features depends 
on the version of Pro Tools software you are 
running. For details on features available with 
your version of Pro Tools, visit the Digidesign 
website.

Summary of Contents for SYNC HD








































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands