manualshive.com logo in svg

Digi TransPort LR54-AA401, User Manual

Share
Download
Digi TransPort LR54-AA401 User Manual Download Page 135

Command descriptions

TransPort LR User Guide

182

show dsl

Displays the DSL interface status and statistics.

This group is only supported in LR54, LR54W, LR54D and LR54DWC1 products.

Parameters

description

Description of the DSL interface.

admin-status

Whether the DSL interface is sufficiently configured to be brought up.

oper-status

Whether the DSL interface is up or down.

uptime

Amount of time the DSL interface has been in the Up state.

hardware-version

The hardware version of the DSL modem.

firmware-version

The version of the firmware running on the DSL modem.

system-firmware-id

An identifier of the firmware running on the DSL modem.

line-status

The status of the DSL line.

line-uptime

DSL line uptime, in seconds

line-mode

The operational mode for the DSL interface when it is in the Up state.

encapsulation

The data encapsulation type for the DSL interface.

vpi

Virtual Path Identifier (VPI) for the DSL interface.

vci

Virtual Circuit Identifier (VCI) for the DSL interface.

Summary of Contents for TransPort LR54-AA401










































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands