Diffraction SBIG STC-428-OEM User Manual Download

Page: 6 / 44

SBIG STC-428-OEM CAMERA

USER’S MANUAL

Camera Features

The STC-428-OEM imaging camera features:

•

The high sensitivity, low noise 7 megapixel IMX428 imaging
sensor

•

Two-stage thermoelectric cooling for minimal noise on long
exposures

•

SmartCooling™ active temperature regulation to 0.1 degrees C for

high calibration stability

•

High-speed USB 3.0 interface (USB 2.0 compatible)

•

C and Trigger I/O interface

•

Centered optical axis for optimum instrument balance

•

Multiplatform software API and sample code availability

The STC-428-EVAL evaluation kit also include the Windows-based
MaxIm LT application for image acquisition and processing.

Refer to

Appendix A-2 STC-428-OEM Specifications

for detailed camera

specifications.

Summary of Contents for SBIG STC-428-OEM













































Search results

Summary of Contents for SBIG STC-428-OEM

Reviews:

Related manuals for SBIG STC-428-OEM

Brands by name

Popular brands

Diffraction SBIG STC-428-OEM, User Manual

Search results

Summary of Contents for SBIG STC-428-OEM

Reviews:

Related manuals for SBIG STC-428-OEM

Brands by name

Popular brands