Dibo 3.126.160 Translation Of Original Instructions Download Page 15

 

 

ENGLISH 

 

15 

 

Releasing the brushes on a roller head: repeat the above procedure in reverse.  

 

Attaching the side brushes (when present): to facilitate transport, the side brushes are 
not installed in the operating position.  To install the side brushes, proceed as follows: 

  Unscrew the screws on the side brush motor shaft. 

  Make sure the cotter pin is inserted on the motor shaft.  

  Insert the brush complete with flange on the motor shaft.  

  Screw the locking screw up again. 

Releasing the side brushes: repeat the above procedure in reverse.  

6.5. 

Detergents - Instructions 

 IMPORTANT 

Always dilute the detergent according to the manufacturer's instructions. Do not 

use sodium hypochlorite (bleach) or other oxidants, particularly in strong 

concentrations. Do not use solvents or hydrocarbons.  The temperature of the 

water and detergent must not exceed the maximum indicated in the technical 

specification. They must be free of sand and/or other impurities. 

The  machine  has  been  designed  for  use  with  low-foam  biodegradable  detergents  made 
specifically for scrubber driers. 
For a complete and up-to-date list of the detergents and chemicals available, contact the 
Manufacturer. 
Use products suitable for the floor and dirt to be removed only. 
Follow  the  safety  regulations  on  use  of  detergents  given  in  the  section  "Safety 
regulations". 

6.6. 

Preparing the machine for work 

 IMPORTANT 

Before starting work, wear overalls, ear protectors, non-slip waterproof shoes, 

mask to protect the respiratory tract, gloves and all other personal protection 

devices recommended by the supplier of the detergent used or necessitated by the 

work environment. 

Before starting work, proceed as follows: 

  check the battery charge (charge if necessary); 

  make sure the dirty water tank (fig. A, ref. 2) is empty. If necessary, empty it; 

  via  the  opening,  fill  the  detergent  tank  (fig.  A,  ref.  1)  with  a  suitable  concentration  of 

clean  water  and  low-foam  detergent.  Leave  at least 5 cm between the surface of the 
liquid and the opening of the tank; 

  if the machine is fitted with the optional CHEM DOSE accessory, fill the CHEM DOSE 

tank (fig. G, ref. 2) with appropriately diluted low-foam detergent. 

  mount the most suitable brushes or drive disks for the floor and work to be performed 

(see paragraph 3.4); 

  make sure the squeegee (fig. E) is firmly attached and connected to the suction hose 

(fig. E, ref. 2). Make sure the back blade is not worn. 

 

i INFORMATION 

If you are using the machine for the first time, we recommend trying it on a large 

obstacle-free surface first to acquire the necessary familiarity.  

Always empty the dirty water tank before filling the detergent tank again. 

For effective cleaning and to extend the working life of the machine, follow a few simple 
rules:  

Summary of Contents for 3.126.160




























Reviews: