Home
/
Diamond
/
DSL602EU
/
User Manual

Diamond DSL602EU, User Manual

Share

23 pages before
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44

Page: 38 / 44

Diamond DSL602EU User Manual Download Page 38

DSL602EU User’s Manual

6.4.6.4 TR-069

The TR-069 (CPE WAN Management Protocol) function can secure remote
host access to your DSL602EU from LAN interface for some services
provided by it.

Field Description
Inform

Enable/disable the DSL602EU to connect to the ACS
periodically.

Inform Interval

This field is enabled only when the Inform Enabled field
is checked. It defines the amount of time (in seconds)
between a successful connection with an ACS server
and a new attempt to connect to an ACS server.

ACS URL

Enter the URL of the Auto Configuration Server (ACS)
provided by the ISP.

ACS User Name

Enter the user name for the ACS to authenticate.

ACS Password

Enter the password for the ACS to authenticate.

Display SOAP
messages on
serial console

Enable/disable whether display SOAP messages on
serial console.

Connection
Request
Authentication

Enable/disable to authenticate an ACS making a
connection request to the DSL602EU.

36

«
...
36
37
38
39
40
...
»

Summary of Contents for DSL602EU













































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands