Tension ring
M45018
Hat S
M45009
S trap
M45006
Hat
M45008
Hat SS
M45010
Hat ring
M45011
Screw with radial
element fastener ring
Nut with radial
element fastener ring
Screw with radial element holder
Radial coil for 3.5MHz
M45015
Pipe No. 1
φ
7.4
M45001
Pipe No. 2
φ
10
M45002
Pipe No. 3
φ
30
M45003
Pipe No. 4
φ
30
M45004
Pipe No. 5
φ
30
M45005
Tapping screw M4x8
M45021
Tapping screw M4x8
M45021
Tapping screw M4x8
M45021
Tapping screw M4x8
M45021
Tapping screw M4x8
M45021
Tapping screw M4x8
M45021
Inner tooth washer M4
M45022
Inner tooth washer M4
M45022
Inner tooth washer M4
M45022
Inner tooth washer M4
M45022
Inner tooth washer M4
M45022
Inner tooth washer M4
M45022
Loading Coil for 7MHz
M45007
Mast bracket
M45019
Radial nut
M45025
Radial coil for 7MHz
M45016
Support pipe
M45014
Radial ring
M45013
Radial element
M45017
Feeding point assembly
M45012
Hex head screw M6x8
M45023
Hex head screw M6x8
M45023
Spring washer M6
M45024
Spring washer M6
M45024
V-volt set
M45020
80m and 40m Dual-band Vertical Antenna
CP8040
・
Parts Description
Operation Instructions
（
Fig
１）
・
Description
①
The CP8040 is a dual-band
vertical
antenna for HF low band.
②
Compact, light weighted and very
easy to assemble.
③
It is completely self-supported and
does not need any guy wires.
④
Trap radials could be concentrated
on one direction instead of
spreading them around the
antenna. This is especially
convenient if the antenna is
installed on balcony railing or
window side of condominiums and
urban
apartments.
⑤
Since the antenna is direct DC
ground at the feed point, coaxial
cable and
transceiver are being
protected from the high voltage
caused by lighting.
⑥
Center frequencies of the antenna
are adjustable in each band
simply by
change radial length
and capacity hat (80m only).
⑦
Top loading structure utilizing
capacitive
hat
enables
the
antenna to complete with full
quarter wave length antennas in
its performance.
⑧
It is rigid and rugged enough to
withstand the wind pressure over
35m/sec.
⑨
Mast brackets area adjustable to
accept 1 1/5” to 2 1/3” diameter
mast.
⑩
Since feeding point is covered by
the support pipe, it is excellent in
the waterproof property.
⑪
CP8040 can be used 3.5-3.8MHz /
7-7.2MHz.
・
Parts Description
Parts #
Description
Qty
M45001 Pipe No. 1
φ
7.4 1
M45002 Pipe No. 2
φ
10 1
M45003 Pipe No. 3
φ
30 1
M45004 Pipe No. 4
φ
30 1
M45005 Pipe No. 5
φ
30 1
M45006 S trap 1
M45007 Loading coil for 7MHz 1
M45008 Hat
2
M45009 Hat S
4
M45010 Hat SS
4
M45011 Hat ring
1
M45012 Feeding point assembly 1
M45013 Radial ring
1
M45014 Support pipe
1
M45015 Radial coil for 3.5MHz 1
M45016 Radial coil for 7MHz 1
M45017 Radial element
2
M45018 Tension ring
2
M45019 Mast bracket
2
M45020 V-volt set
2
M45021 Tapping screw M4x8
12
M45022 Inner tooth washer M4 12
M45023 Hex head screw M6x8 3
M45024 Spring washer M6 3
M45025 Radial nut
2
