manualshive.com logo in svg

Dialogic 4000 Media Gateway Series, Reference Manual

Share
Download
Dialogic 4000 Media Gateway Series Reference Manual Download Page 21

 

Dialogic® 4000 Media Gateway Series Reference Guide

page 21

Network Interfaces

The 

Network Interfaces

 configuration allows for configuring the global network parameters of the

 

Dialogic

®

 Diva

®

 SIPcontrol

TM

 software, such as the IP addresses and the ports on which the Diva SIPcontrol 

software will be listening. The Diva SIPcontrol software supports only a single IP address.

To open the online help for a specific parameter, click the parameter and a window with the help text will pop up.

You may configure the parameters shown in the graphic and explained below:  

Name

Displays the name of the installed Ethernet adapter. The preset designation may be replaced 
with a unique identifier, such as "Internal Network".

Device

Displays the complete description of the installed Ethernet adapter assigned by the operating 
system.

IP address

Displays the IP address of the computer on which the Diva SIPcontrol software is installed. 

UDP listen port

If you use UDP as IP protocol for calls from SIP, enable the check box to display the standard 
port number 5060. This standard port can be used if no other SIP application is running on the 
same computer as the Diva SIPcontrol

 

software. Note that you may only enable one network 

interface.

TCP listen port

If you use TCP as IP protocol for calls from SIP, enable the check box to display the standard 
port number 5060. This standard port can be used if no other SIP application is running on the 
same computer as the Diva SIPcontrol

 

software. Note that you may only enable one network 

interface.

TLS listen port

If you use TLS for encrypted calls, enable the check box to display the standard port number 
5061. You may change the port number, but it must not be the same as the 

TCP Listen Port

 

number. Note that you may only enable one network interface. If you use TLS, you need to 
upload security certificates and set the cipher level in the 

Security Profiles

 on page 30. 

RTP start port

Defines the lowest port of the range in which the Diva SIPcontrol software sends and receives 
RTP streams. Change this value only if problems occur.

RTP end port

Defines the highest port of the range in which the Diva SIPcontrol software sends and receives 
RTP streams. Change this value only if problems occur.

Summary of Contents for 4000 Media Gateway Series













































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands