Di-soric ID-06 Quick Start Manual Download Page 1

   

Step 1 — Check Hardware

Item

Description

Part Number

1

ID-06 C-Mount Industrial Imager

ID-06-IXX-00-ES

2

Interface Device

VSID-IB-ES

Note:

 Additional cordsets and accessories are available in the di-soric Product Catalog.

Caution:

 Be sure that all connections are secure 

BEFORE

 

applying power. Power down 

BEFORE

 disconnecting any cables.

Ethernet Standalone

1

2

 

Quick Start Guide

ID-06 C-Mount            

Industrial Imager

P/N 83-116801 Rev A

Step 2 — Connect the System

Important:

 When connecting cordsets to the ID-06 C-Mount 

and VSID-IB-ES, align the pins first and then push the connec-
tor into place. Do not twist the connectors, as this will bend the 
pins.

Important:

 Do not attempt to power more than four imagers 

with  a single power supply in a daisy chain configuration. Add a 
VSID-IB-ES and one power supply for every four additional 
imagers in the daisy chain.

RS-232

1. Connect the Serial Communication Cable from “A” on the 

ID-06 C-Mount to “2” on the VSID-IB-ES. 

2. Connect the host cable from “1” on the VSID-IB-ES to the 

host computer.

3. Connect the photo sensor to “T” on the VSID-IB-ES.
4. Connect the power supply to “3” on the VSID-IB-ES.
5. Plug in the power supply.

Ethernet

1. Connect the Ethernet Cable from “B” on the ID-06      C-

Mount to the network.

2. Connect the power supply to “A” on the ID-06              C-

Mount.

3. Connect the photo sensor to “T” on the VSID-IB-ES.
4. Plug in the power supply.

Step 3 — Position the Imager

1. Position the imager at a focal distance of one inch or more from 

a test symbol.

2. Tip the imager relative to the symbol to avoid the glare of direct 

(specular) reflection. The case parting line should be perpendicular 
to the plane of the symbol by either pitching the symbol or the 
imager as shown.

3. Symbols can be rotated (tilted) at any angle; however, for best 

results symbols should be aligned with the field of view. In the 
case of linear symbols, aligning the bars in the direction of their 
movement (ladder orientation) will minimize the chances of 
blurring and will result in more consistent decodes.

Important:

 Avoid excessive skew or pitch. Maximum skew is 

±30°

; maximum pitch is 

±30°

Step 4 — Install di-soric ID

di-soric ID Software can be found on the di-soric USB-Stick 
that is packaged with the ID-06 C-Mount. 

1. Follow the prompts to install di-soric ID from the Tools 

Drive.

2. Click on the di-soric ID icon to run the program.

Note: 

di-soric ID can also be installed from the 

Down-

load Center

 at  

www.di-soric.com

.

Minimum System Requirements

• 233 MHz Pentium processor
• Windows 7 (32-bit or 64-bit), Vista (32-bit or 64-bit), XP, or 

2000 operating system

• Internet Explorer 6.0 or higher
• 128 MB RAM or greater
• 80 MB hard drive space
• 800 x 600 minimum 256 color display (1024 x 768 32-bit color 

recommended)

Refer to the 

ID-06 Industrial Imager User’s Manual

 for detailed 

information about using di-soric ID to configure the ID-06 C-
Mount.

Reviews: