background image

3.5 PV Connection

3.5.1 PV Module Selection:

3. Then,insert AC output wires according to polarities indicated on the terminal block and 
    tighten terminal. Be sure to connect corresponding N wires and PE wires to related 
    terminals as well.
4. Make sure the wires are securely connected. 
5. Appliances such as air conditioner are required at least 2-3 minutes to restart because it 
    is required to have enough time to balance refrigerant gas inside of circuit.If a power 
    shortage occurs and recovers in short time,it will cause damage to your connected 
    appliances.To prevent this kind of damage,please check manufacturer of air conditioner 
    if it is equipped with time-delay function before installation.Otherwise,this inverter will 
    trigger overload fault and cut off output to protect your appliance but sometimes it still 
    causes internal damage to the air conditioner.

When selecting proper PV modules, please be sure to consider below parameters:
1) Open circuit Voltage (Voc) of PV modules not exceeds max. PV array open circuit 
     voltage of inverter. 
2) Open circuit Voltage (Voc) of PV modules should be higher than min. start voltage.

Before connecting to PV modules,please install a separately DC circuit breaker between 
inverter and PV modules.It is very important for system safety and efficient operation to 
use appropriate cable for PV module connection.To reduce risk of injury,please use the 
proper recommended cable size as below.

Be sure that AC power source is disconnected before attempting to wire it to 
the unit.

To avoid any malfunction, do not connect any PV modules with possible 
current leakage to the inverter. For example, grounded PV modules will 
cause current leakage to the inverter. When using PV modules, please be 
sure NO grounding.

It is requested to use PV junction box with surge protection. Otherwise,it 
will cause damage on inverter when lightning occurs on PV modules.

Chart 3-5

Chart 3-2 Cable size

Model

3.6/5KW

Wire Size

1X12AWG

Cable(mm   )

2

4

PV Input Voltage (V)

Inverter Model

3.6KW

5KW

370V(100V~500V)

125Vdc-425Vdc

PV Array MPPT Voltage Range

No. of MPP Trackers

No. of Strings per MPP Tracker

2

1+1

- 11 -

- 12 -

Summary of Contents for SUN-3.6K-SG03LP1-EU




















Reviews: