Dexcowin COCOON DX-7020 User Manual Download Page 49

Page: 49 / 61

(Model: DX-7020) User Manual

5.2 Troubleshooting

Problem

Cause

Solution

Nothing lights up

The battery level is low

Connect the device to a

charger.

No X-ray emission

The generator is preparing to

emit radiation, so there is no

display on the screen.

Wait about five seconds until

the X-ray emits radiation

Button or trigger defective.

Call a qualified service

technician.

X-ray emission

works, but the

image is too bright

or completely white

Receptor defective.

Call a qualified service

technician.

The patient is positioned

incorrectly

Adjust the position of the

patient according to the user

manual.

Exposure time is too short.

Increase the exposure time.

Device defective.

Call a qualified service

technician.

X-ray emission

works, but the

image is too dark

Receptor defective.

Change the receptor or

compare it with another

receptor.

Exposure time is too long.

Decrease the exposure time.

Device defective.

Call a qualified service

technician.

Summary of Contents for COCOON DX-7020






























































Search results

Summary of Contents for COCOON DX-7020

Reviews:

Related manuals for COCOON DX-7020

Brands by name

Popular brands

Dexcowin COCOON DX-7020, User Manual

Search results

Summary of Contents for COCOON DX-7020

Reviews:

Related manuals for COCOON DX-7020

Brands by name

Popular brands