background image

DS-TACHO-1  

TECHNICAL REFERENCE MANUAL 

 

 

5.5. Printing History 

Version V20-1, Released 2020 Last changed: 14. September 2020 at 13:25. 

 

5.6. Copyright 

Copyright © 2015-2019 Dewesoft d.o.o. This document contains information which is protected by

   

 

 

 

 

 

 

 

   

 

 

copyright. All rights are reserved. Reproduction, adaptation, or translation without prior written

 

 

 

 

 

 

 

 

 

 

 

 

permission is prohibited, except as allowed under the copyright laws. All trademarks and registered

   

 

 

 

 

 

 

 

 

 

 

 

 

trademarks are acknowledged to be the property of their owners. 

 

5.7. Trademarks 

We take pride in our products and we take care that all key products and technologies are registered as

 

 

   

 

 

 

 

 

 

   

 

 

 

 

 

   

trademarks all over the world. The Dewesoft name is a registered trademark. Product families

 

 

 

 

 

 

 

     

 

 

 

 

(KRYPTON, SIRIUS, DSI, DS-NET) and technologies (DualCoreADC, SuperCounter, GrandView) are

 

 

 

 

 

 

 

 

 

 

registered trademarks as well. When used as the logo or as part of any graphic material, the registered

 

   

 

 

   

 

     

   

 

 

 

 

 

trademark sign is used as a part of the logo. When used in text representing the company, product or

 

   

     

   

 

 

 

   

 

 

 

 

   

technology name, the ® sign is not used. The Dewesoft triangle logo is a registered trademark but the ®

 

 

   

   

 

 

 

 

 

     

 

 

 

   

sign is not used in the visual representation of the triangle logo. 

 
 

6. Safety instructions 

Your safety is our primary concern! Please be safe! 

 

6.1. Safety symbols in the manual 

 

 

Warning  
Calls attention to a procedure, practice, or condition that could cause the body injury or death  
 

 

Caution 
Calls attention to a procedure, practice, or condition that could possibly cause damage to

 

 

   

 

 

 

 

 

 

 

 

 

 

equipment or permanent loss of data.  

 

6.2. General Safety Instructions 

 

 

Warning 
The following general safety precautions must be observed during all phases of operation, service,

 

 

 

 

 

 

 

 

   

   

 

 

and repair of this product. Failure to comply with these precautions or with specific warnings

 

   

 

 

   

 

 

 

   

 

 

 

elsewhere in this manual violates safety standards of design, manufacture, and intended use of

   

 

 

 

 

   

 

 

 

 

   

the product. Dewesoft GmbH assumes no liability for the customer’s failure to comply with these

 

 

 

 

 

 

 

 

 

 

   

 

 

 

requirements.  

 

DS-TACHO-1 V20-1

9/13   

Summary of Contents for DS-TACHO-1














Reviews: