Dewert User Manual 2000XL Series– Updated 05.2021/1 MDR Page 8 of 19
the side guard to fold down through its own weight. Allow the side guard to fold all the way down until it
engages automatically.
Please note: Due to the two guides and guide pins, a small amount of force is only necessary when releasing
the lock (= briefly removing the side guard guide pins). Do not pull or push when allowing the side guard to
fold down (hardly any force is required).
Folding up the side guard: Grasp the side guard with one hand in the middle of the guard frame at the end
facing downwards (or with two hands on the left and right at the top). Push the side guard upwards and
outwards slightly, thereby releasing the lock. Now hold the side guard loosely and fold it up until it engages.
Please note:
Do not use the side guard as a push handle.
Laterally lowerable side guard (optional)
(Standard for models 2210XLE, 2210XL/H, 2215XL/H, 2250XL/H, 2255XL/H)
Operating the side guard:
Hold the centre of the rail of the side guard with one hand and release it by moving it
minimally sideways (either towards the head or foot part). At the same time, use your other hand to pull out
and turn the locking pin (red knob) located in the centre of the side guard underneath the upholstery frame.
Press down or pull up the side guard using the rail until the locking pin engages audibly. After the locking pin
has engaged, the side guard is secured in place. To check whether the
side guard has engaged properly, move it sideways on the rail (either towards the head or foot part). Only
limited movement should then be noticeable.
Always operate the side guard with the necessary caution. Never operate the side guard if the hands,
fingers, etc. of another person are located between the bars or on the mechanism of the side guard.
Risk of being crushed/pinched!!!
The laterally lowerable side guard is completely screwed in place. If the side guard becomes too loose or has
excessive lateral play over time due to use, it can be readjusted by tightening the screws. The moving parts of
the side guard should be re-lubricated slightly at regular intervals
(spray oil, e.g. Ballistol).
Side guard, lowerable, for side rail
This side guard can be placed and fixed on any side rail using a clamp. By loosening the toggle screw of the
clamp, the position and height of the inserted side guard can be shifted and adjusted respectively. Complete
lowering below the upholstery level can only be achieved if the guide points
in the direction of the upholstery when the side guard is inserted into the clamp.
Please note:
Never use the side guard as a push handle. It has not been designed for this purpose.
2.7 Echocardiography tables
The table for echocardiography treatment has a cut-out on the left-hand side in the upholstered surface. It can
be closed with a cushion. The cushion can be pushed out from the bottom upwards (a slight amount of
pressure is required). To close the cut-out, first place the cushion in the rear of the cut-out and then press it
down into the upholstered surface (a slight amount of pressure is required). The lower side of the cut-out is
not parallel to the upper side. There is a visible slant. The position of the cushion in the cut-out is thus clearly
identifiable and there is no risk of it being accidentally pushed out.
Caution: Do not reach under the cushion or into the open cut-out during height adjustment. Always
remove instruments/equipment from the cut-out area before adjusting the height.
Potential equalisation connector
A potential equalisation connector according to DIN 42801 is attached to the long side of the underframe on
the left (side with the upholstery cut-out). This connection must be used if interference from electromagnetic
radiation can be seen on the monitors during the examination, which could falsify the measured values.
Despite compliance with the applicable EMC regulations, the use of highly sensitive examination equipment
can cause this minimal radiation to become visible. Only use connectors that comply with DIN. Through
additional wiring of the individual assemblies, there is conductive contact between them.
The potential equalisation connector is marked with the symbol
.
