background image

4

  C.  Forward/reverse lever 

I.  Mode selector

 D. Chuck 

J. Main handle

  E.  Cord protector with key holder
 F. Cord set

INTENDED USE

These heavy-duty variable speed percssion drills are designed for professional drilling.

DO NOT 

use under wet conditions or in presence of flammable liquids or gases.

These heavy-duty percussion drills are professional power tools. 

DO NOT

 let children come into contact with the tool. Supervision is required when 

inexperienced operators use this tool.

ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of injury, turn unit off and disconnect tool from 

power source

 

before installing and removing accessories, before adjusting or 

changing set-ups or when making repairs. 

Be sure the trigger switch is in the OFF 

position. An accidental start-up can cause injury.

Side Handle (fig. 1)

WARNING:

 

To reduce the risk of personal injury, 

ALWAYS 

operate the tool with the 

side handle properly installed. Failure to do so may result in the side handle slipping 

during tool operation and subsequent loss of control. Hold tool with both hands to 

maximize control.
A side handle comes assembled with the DWD024S-XE. The side handle (G) can be 

adjusted to suit both right-hand and left-hand users.

TO ADJUST THE SIDE HANDLE

  1. Loosen the side handle (G) by turning it counterclockwise.
  2. Rotate the side handle to the desired position.
  3. Tighten the side handle by turning it clockwise.

TO CHANGE SIDES

For right-hand users: slide the side handle clamp over the chuck, handle at the left. 
For left-hand users: slide the side handle clamp over the chuck, handle at the right.

    –  Risk of personal injury due to flying particles.
    –  Risk of personal injury due to prolonged use.

SAVE THESE INSTRUCTIONS FOR FUTURE USE

Motor

Your D

E

WALT tool is powered by a D

E

WALT-built motor. Be sure your power supply 

agrees with the nameplate markings. Voltage decrease of more than 10% will cause 

loss of power and overheating. All D

E

WALT tools are factory tested.

FIG. 1

A

B

D

C

F

E

G

J

C

SHOWN IN 

FORWARD 

POSITION

A

I

COMPONENTS (Fig. 1)

WARNING: 

Never modify the power tool or any part of it. Damage or personal 

injury could result.
  A.  Variable speed trigger switch 

G.  Side handle

  B.  Lock-on button 

H.  Depth adjustment rod

Summary of Contents for DWD024S-XE













Reviews: