ENGLISH
54
c. Contact trip
d. Depth adjustment wheel
e. Low battery and jam/stall indicator light
f. Stall release lever
g. Magazine
h. Pusher latch
i. Mode selector switch (DCN690 & DCN692 only)
j. Rotating rafter/belt hook
k. On-board hex wrench
l.
Battery
pack
m. Non-mar tip
n. Speed selector switch (DCN692 only)
INTENDED USE
The DCN690, DCN691 and DCN692 cordless
framing nailers have been designed for driving nails
into wooden workpieces.
The DCN690 and DCN692 cordless framing nailers
are designed for sequential/bump modes. Nailers
designed for sequential/bump modes
MUST NOT
be used on scaffoldings, stairs, ladders or ladder-like
constructions, e.g., roof laths. For exemptions check
your local national workplace regulations.
The DCN691 cordless framing nailer is designed
for sequential only mode. Nailers designed for
sequential only mode
MAY BE
used on scaffoldings,
stairs, ladders or ladder-like constructions, e.g., roof
laths.
DO NOT
use under wet conditions or in presence of
flammable liquids or gases.
These cordless nailers are professional power tools.
DO NOT
let children come into contact with the
tool. Supervision is required when inexperienced
operators use this tool.
• This product is not intended for use by persons
(including children) suffering from diminished
physical, sensory or mental abilities; lack of
experience, knowledge or skills unless they are
supervised by a person responsible for their
safety. Children should never be left alone with
this product.
Electrical Safety
The electric motor has been designed for one
voltage only. Always check that the battery pack
voltage corresponds to the voltage on the rating
plate. Also make sure that the voltage of your
charger corresponds to that of your mains.
Your D
E
WALT charger is double insulated
in accordance with EN 60335; therefore
no earth wire is required.
If the supply cord is damaged, it must be replaced
by a specially prepared cord available through the
D
E
WALT service organisation.
Mains Plug Replacement
(U.K. & Ireland Only)
If a new mains plug needs to be fitted:
• Safely dispose of the old plug.
• Connect the brown lead to the live terminal in
the plug.
• Connect the blue lead to the neutral terminal.
WARNING:
No connection is to be
made to the earth terminal.
Follow the fitting instructions supplied with good
quality plugs. Recommended fuse: 3 A.
Using an Extension Cable
An extension cord should not be used unless
absolutely necessary. Use an approved extension
cable suitable for the power input of your charger
(see
Technical Data
). The minimum conductor size
is 1 mm
2
; the maximum length is 30 m.
When using a cable reel, always unwind the cable
completely.
ASSEMBLY AND ADJUSTMENTS
WARNING: Prior to assembly and
adjustment, always remove the
battery pack. Always lock off the
tool before inserting or removing
the battery pack.
WARNING:
Use only D
E
WALT battery
packs and chargers.
Inserting and Removing the
Battery Pack from the Tool (fi g. 2)
WARNING: To reduce the risk of
serious personal injury, lock tool
off and disconnect battery pack
before making any adjustments or
removing/installing attachments or
accessories.
An accidental start-up
can cause injury.
NOTE:
Make sure your battery pack (l) is fully
charged. The battery packs supplied will not
necessarily be fully charged.
Summary of Contents for DCN690
