ENGLISH
10
Inserting and Removing the
Battery Pack from the Tool (fig. 3)
WARNING: To reduce the risk
of serious personal injury, place
the forward/reverse button in
the lock-off position or turn tool
off and disconnect battery pack
before making any adjustments or
removing/installing attachments or
accessories.
An accidental start-up
can cause injury.
NOTE:
Make sure your battery pack (g) is fully
charged.
TO INSTALL THE BATTERY PACK INTO THE TOOL HANDLE
1. Align the battery pack with the rails inside the
handle.
2. Slide it firmly into place until you hear the lock
snap into place.
TO REMOVE THE BATTERY PACK FROM THE TOOL
1. Press the release button (f) and firmly pull the
battery pack out of the tool handle.
2. Insert battery pack into the charger as
described in the charger section of this manual.
OPERATION
Instructions for Use
WARNING:
Always observe the safety
instructions and applicable regulations.
WARNING: To reduce the risk
of serious personal injury, place
the forward/reverse button in
the lock-off position or turn tool
off and disconnect battery pack
before making any adjustments or
removing/installing attachments or
accessories.
Proper Hand Position (fig. 1, 8)
WARNING:
To reduce the risk of
serious personal injury,
ALWAYS
use
proper hand position as shown.
WARNING:
To reduce the risk of
serious personal injury,
ALWAYS
hold
securely in anticipation of a sudden
reaction.
Proper hand position requires one hand on the main
handle (i).
Variable Speed Trigger Switch (fig. 1)
To turn the tool on, squeeze the trigger switch (a). To
turn the tool off, release the trigger switch. Your tool
is equipped with a brake. The chuck will stop when
the trigger switch is fully released.
The variable speed switch enables you to select the
best speed for a particular application. The further
you squeeze the trigger, the faster the tool will
operate. For maximum tool life, use variable speed
only for starting holes or fasteners
NOTE:
Continuous use in variable speed range is
not recommended. It may damage the switch and
should be avoided.
Forward/Reverse Control Button
(fig. 1)
A forward/reverse control button (b) determines the
direction of the tool and also serves as a lock-off
button.
To select forward rotation, release the trigger switch
and depress the forward/reverse control button on
the right side of the tool.
To select reverse, depress the forward/reverse
control button on the left side of the tool. The center
position of the control button locks the tool in the off
position. When changing the position of the control
button, be sure the trigger is released.
NOTE:
The first time the tool is run after changing the
direction of rotation, you may hear a click on start up.
This is normal and does not indicate a problem.
Worklight (fig. 1)
There is a worklight (h) located under the torque
adjustment collar (c). The worklight will be activated
when the trigger switch is squeezed.
NOTE:
The worklight is for lighting the immediate
work surface and is not intended to be used as a
flashlight.
Torque Adjustment Collar (fig. 1)
The torque adjustment collar (c) is clearly marked
with numbers and a drill bit symbol.The collar should
be rotated until the desired setting is located at the
top of the tool. Locators are provided in the collar to
eliminate the guess work when selecting fastening
torque. The higher the number on the collar, the higher
the torque and the larger the fastener which can be
driven. To lock the clutch for drilling operations, move
to the drill bit position.
NOTE:
When using the drill/driver for drilling holes, be
sure that the torque adjusting collar is set so the figure
of the drill is aligned with the center line on the top of
Summary of Contents for DCD700
