35
ENGLISH
CLEANING THE WORKLIGHT LENS (FIG 16A–16F)
For the best worklight (a9) performance, perform the following maintenance
regularly.
• Carefully clean sawdust and debris from worklight lens with a cotton
swab.
• DO NOT use solvents of any kind; they may damage the lens.
• Dust build-up can block the worklight and prevent it from accurately
indicating the line of cut.
To Remove Worklight
1. Raise the saw bench table to its highest position then raise the saw
head to its highest position.
2. Turn the black sleeve (a10) a 1/4 turn anti-clockwise to disassemble.
3. Unplug the wire (a11) to the worklight.
4. Remove the screws (a12) using the T30 star wrench.
5. Slide the LED aluminium housing out then down past the underside of
the table.
6. Clean the worklight lens (a13) with a cotton swab.
7. Re-install the LED aluminum housing to the table.
8. Reassemble the worklight by following the above steps in reverse order.
Lubrication
Lubrication may only be needed in the link slot (fig. 18).
If the saw head movement is not smooth or seems sticky during a mitre cut,
proceed as follows:
1. Unplug the saw.
2. Remove the blade (refer to
Changing the Saw Blade
).
3. Clean the link slot (a15) (located behind the spindle) of dust and wood
chips, then add several drops of lubricant into the slot.
4. Check if movement is smoother.
5. Reassemble the blade.
Optional Accessories
WARNING:
Since accessories, other than those offered by
D
E
WALT, have not been tested with this product, use of such
accessories with this tool could be hazardous. To reduce the
risk of injury, only D
E
WALT-recommended accessories should
be used with this product.
SUPPORT FOR LONG PIECES (FIG. 4)
• Always support long pieces.
• For best results, use the extension work support (kk) to extend the table
width of your saw (available from your dealer as an option). Support
long workpieces using any convenient means such as saw-horses or
similar devices to keep the ends from dropping.
DUST COLLECTION PORT (FIG. 10)
WARNING!
Whenever possible, connect a dust extraction
device designed in accordance with the relevant regulations
regarding dust emission.
The D27113 is supplied with three dust collection ports.
Connect a dust collection device designed in accordance with the relevant
regulations. The air velocity of externally connected systems shall be 20 m/s
±2 m/s. Velocity to be measured in the connection tube at the point of
connection, with the tool connected but not running.
SAW BLADES
ALWAYS USE noise reduced 305 mm (12") SAW BLADES WITH 30 mm
ARBOUR HOLES. SPEED RATING MUST BE AT LEAST 3500 RPM.
Never use a smaller diameter blade. It will not be guarded properly.
Use crosscut blades only! Do not use blades designed for fast ripping,
combination blades or blades with hook angles in excess of 5°.
BLADE DESCRIPTIONS
APPLICATION
DIAMETER
TEETH
Construction Saw Blades
(thin kerf with anti-stick rim)
General Purpose
305 mm (12")
40
Fine Crosscuts
305 mm (12")
60
Consult your dealer for further information on the appropriate accessories.
Protecting the Environment
Separate collection. This product must not be disposed of with
normal household waste.
Should you find one day that your D
E
WALT product needs replacement, or
if it is of no further use to you, do not dispose of it with household waste.
Make this product available for separate collection.
Separate collection of used products and packaging allows
materials to be recycled and used again. Re-use of recycled
materials helps prevent environmental pollution and reduces the
demand for raw materials.
Local regulations may provide for separate collection of electrical
products from the household, at municipal waste sites or by the retailer
when you purchase a new product.
D
E
WALT provides a facility for the collection and recycling of D
E
WALT
products once they have reached the end of their working life. To take
advantage of this service please return your product to any authorised repair
agent who will collect them on our behalf.
You can check the location of your nearest authorised repair agent by
contacting your local D
E
WALT office at the address indicated in this manual.
Alternatively, a list of authorised D
E
WALT repair agents and full details
of our after-sales service and contacts are available on the Internet at:
www.2helpU.com
.
Та
ше
в
-
Га
лв
ин
г
ОО
Д
www.tashev-galving.com
