background image

4

HAZARD TO LOOK FOR

Compressed Gas

Excessive Operating Pressure

Unsuitable Cleaning Solvents

WHAT COULD HAPPEN

Oxygen will react with oil in tool causing
an explosion. Flammable gases will ig-
nite from sparking and cause the tool to
explode.

THE  TOOL  COULD  EXPLODE!

Flammable vapors in the tool will ignite
by a spark and could cause the tool to
explode!

HOW TO PREVENT IT

Do not use any type of flammable
gases or oxygen as a power source
for the tool.

Use only filtered, lubricated, regu-
lated compressed air .

Operate tool with clean dry air, regu-
lated to 100 psi pressure maximum.

Never use gasoline or other flam-
mable liquids to clean the tool.

Risk of explosion.

SAFETY GUIDELINES - DEFINITIONS

IMPORTANT SAFETY INFORMATION - A
HAZARD THAT 

MIGHT 

CAUSE SERIOUS

INJURY OR LOSS OF LIFE.

Information that you should pay special
attention to.

URGENT SAFETY INFORMATION - A HAZARD
THAT WILL CAUSE SERIOUS INJURY OR LOSS
OF  LIFE.

This manual contains informa-
tion that is important for you to
know and understand. This infor-
mation relates to protecting 

YOUR

SAFETY

 and 

PREVENTING

 

EQUIP-

MENT PROBLEMS

. To help you

recognize this information, we use
symbols to the right. Please read
the manual and pay attention to
these sections.

Information for preventing damage to
equipment.

IMPORTANT SAFETY INSTRUCTIONS

•  SAVE THESE INSTRUCTIONS •

IMPROPER OPERATION OR MAINTENANCE OF THIS PRODUCT COULD RESULT
IN SERIOUS INJURY AND PROPERTY DAMAGE. READ AND UNDERSTAND ALL
WARNINGS AND OPERATING INSTRUCTIONS BEFORE USING THIS EQUIPMENT

.

Summary of Contents for AFN5

















Reviews: